Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 73)

Brocade Mobility RFS Controller CLI Reference Guide 55
53-1003098-01
2
mint traceroute {(destination-port <1-65535>|max-hops <1-255>|
source-port <1-65535>|timseout <1-255>)}
Example
rfs7000-37FABE>mint ping 70.37.FA.BF count 20 size 128
MiNT ping 70.37.FA.BF with 128 bytes of data.
Response from 70.37.FA.BF: id=1 time=0.292 ms
Response from 70.37.FA.BF: id=2 time=0.206 ms
Response from 70.37.FA.BF: id=3 time=0.184 ms
Response from 70.37.FA.BF: id=4 time=0.160 ms
Response from 70.37.FA.BF: id=5 time=0.138 ms
Response from 70.37.FA.BF: id=6 time=0.161 ms
Response from 70.37.FA.BF: id=7 time=0.174 ms
Response from 70.37.FA.BF: id=8 time=0.207 ms
Response from 70.37.FA.BF: id=9 time=0.157 ms
Response from 70.37.FA.BF: id=10 time=0.153 ms
Response from 70.37.FA.BF: id=11 time=0.159 ms
Response from 70.37.FA.BF: id=12 time=0.173 ms
Response from 70.37.FA.BF: id=13 time=0.156 ms
Response from 70.37.FA.BF: id=14 time=0.209 ms
Response from 70.37.FA.BF: id=15 time=0.147 ms
Response from 70.37.FA.BF: id=16 time=0.203 ms
Response from 70.37.FA.BF: id=17 time=0.148 ms
Response from 70.37.FA.BF: id=18 time=0.169 ms
Response from 70.37.FA.BF: id=19 time=0.164 ms
Response from 70.37.FA.BF: id=20 time=0.177 ms
--- 70.37.FA.BF ping statistics ---
20 packets transmitted, 20 packets received, 0% packet loss
round-trip min/avg/max = 0.138/0.177/0.292 ms
rfs7000-37FABE>
no
User Exec Commands
Use the
no
command to revert a command or to set parameters to their default. This command
turns off an enabled feature or reverts settings to default.
NOTE
The commands have their own set of parameters that can be reset.
Supported in the following platforms:
traceroute Prints the route packets trace to a device
•
– Specify the destination device’s MiNT ID.
destination-port
<1-65535> Optional. Sets the Equal-cost Multi-path (ECMP) routing destination port
•
<1-65535> – Specify a value from 1 - 65535. The default port is 45.
max-hops <1-255> Optional. Sets the maximum number of hops a traceroute packet traverses in the forward direction
•
<1-255> – Specify a value from 1 - 255. The default is 30.
source-port
<1-65535> Optional. Sets the ECMP source port
•
<1-65535> – Specify a value from 1 - 65535. The default port is 45.
timeout <1-255> Optional. Sets the minimum response time period in seconds
•
<1-65535> – Specify a value from 1 sec - 255 sec. The default is 30 seconds.