Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 1303)

Brocade Mobility RFS Controller CLI Reference Guide 1295
53-1003098-01
27
acs priority-meshpoint [2.4GHz|5GHz]
acs sample-count [2.4GHz|5GHz] <1-10>
acs snr-delta [2.4GHz|5GHz] <1-100>
acs signal-threshold [2.4GHz|5GHz] <-100-0>
acs tolerance-period [2.4GHz|5GHz] <10-600>
Example
rfs4000-229D58(config-profile-testAP71XX-meshpoint-test)#acs
channel-hold-time 2.4GHz 2500
rfs4000-229D58(config-profile-testAP71XX-meshpoint-test)#
rfs4000-229D58(config-profile-testAP71XX-meshpoint-test)#acs ocs-duration
2.4GHz 30
acs Configures ACS settings and overrides on the selected meshpoint-device
priority-meshpoint
[2.4GHz|5GHz]
Configures the priority meshpoint. Configuring a priority meshpoint overrides automatic meshpoint
configuration.
•
2.4 GHz – Configures the priority meshpoint for the 2.4 GHz radio band
•
5.0 GHz – Configures the priority meshpoint for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
– Specify the meshpoint name for the selected radio band.
acs Configures ACS settings and overrides on the selected meshpoint-device
sample-count [2.4GHz|5GHz]
<1-10> Configures the minimum number of scan cycle samples to consider for auto channel selection
•
2.4 GHz – Configures the sample count for the 2.4 GHz radio band
•
5.0 GHz – Configures the sample count for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<1-10> – Specify a value from 1 -10. The default is 5 samples.
acs Configures ACS settings and overrides on the selected meshpoint-device
snr-delta [2.4GHz|5GHz]
<1-100> Configures the channel SNR delta. A meshpoint on a candidate channel must have a SNR of a
greater delta than the next hop on the current channel.
•
2.4 GHz – Configures the snr-delta for the 2.4 GHz radio band
•
5.0 GHz – Configures the snr-delta for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<1-100> – Specify a value from 1 - 100 dB. The default is 5 dB.
acs Configures ACS settings and overrides on the selected meshpoint-device
signal-threshold [2.4GHz|5GHz]
<-100-0> Configures the signal strength threshold. If the signal strength of the next hop drops below the
configured signal-threshold, a scan is triggered.
•
2.4 GHz – Configures the signal-threshold for the 2.4 GHz radio band
•
5.0 GHz – Configures the signal-threshold for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<-100-0> – Specify a value from -100 - 0 dB. The default is -65 dB.
acs Configures ACS settings and overrides on the selected meshpoint-device
tolerance-period [2.4GHz|5GHz]
<10-600> Configures the maximum tolerance period in seconds. This is the interval to wait for the root bound to
recovery from a bad link.
•
2.4 GHz – Configures the tolerance-period for the 2.4 GHz radio band
•
5.0 GHz – Configures the tolerance-period for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<10-600> – Specify a value from 10 - 600 seconds. the default is 60 seconds.