Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 1302)

1294 Brocade Mobility RFS Controller CLI Reference Guide
53-1003098-01
27
acs channel-width [2.4GHz|5GHz] [20MHz|40MHz|auto]
acs ocs-duration [2.4GHz|5GHz] <20-250>
acs ocs-frequency [2.4GHz|5GHz] <1-60>
acs path-min [2.4GHz|5GHz] <100-20000>
acs path-threshold [2.4GHz|5GHz] <800-65535>
acs Configures ACS settings and overrides on the selected meshpoint-device
channel-width [2.4GHz|5GHz]
[20MHz|40MHz|auto] Configures the channel width that meshpoint auto channel selection assigns to the radio
•
2.4 GHz – Configures the operating channel width for the 2.4 GHz radio band
•
5.0 GHz – Configures the operating channel width for the 5.0 GHz radio band
The following keywords are common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
20 MHz – Assigns the 20 MHz channel width to the radio
•
40 MHz – Assigns the 40 MHz channel width to the radio
•
auto – Selects and assigns the best possible channel from the 20/40 MHz width. This is the
default setting.
acs Configures ACS settings and overrides on the selected meshpoint-device
ocs-duration [2.4GHz|5GHz]
<20-250> Configures the duration, in milliseconds, of off -channel scans (OCSs)
•
2.4 GHz – Configures the ocs-duration for the 2.4 GHz radio band
•
5.0 GHz – Configures the ocs-duration for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<20-250> – Specify a value from 20 - 250 milliseconds. The default value is
50 milliseconds.
acs Configures ACS settings and overrides on the selected meshpoint-device
ocs-frequency [2.4GHz|5GHz]
<1-60> Configures the interval, in seconds, at which off-channel scan is performed. An
ocs-frequency of 10 seconds means that an off-channel scan will be performed once every 10
seconds.
•
2.4 GHz – Configures the ocs-frequency for the 2.4 GHz radio band
•
5.0 GHz – Configures the ocs-frequency for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<1-60> – Specify a value form 1 - 60 seconds. The default is 6 seconds.
acs Configures ACS settings and overrides on the selected meshpoint-device
path-min [2.4GHz|5GHz]
<100-20000> Configures the minimum root path metric needed for auto channel selection. This is the acceptance
root path metric value to consider a root as a possible candidate mesh node.
•
2.4 GHz – Configures the minimum root path metric for the 2.4 GHz radio band
•
5.0 GHz – Configures the minimum root path metric for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<100-20000> – Specify a value from 100 - 20000. The default is 1000.
acs Configures ACS settings and overrides on the selected meshpoint-device
path-threshold [2.4GHz|5GHz]
<800-65535> Configures the root path metric threshold for auto channel selection. This is the acceptance root path
metric threshold beyond which the root bound to is considered as bad.
•
2.4 GHz – Configures the root path metric threshold for the 2.4 GHz radio band
•
5.0 GHz – Configures the root path metric threshold for the 5.0 GHz radio band
The following keyword is common to the ‘2.4 GHz’ and ‘5.0 GHz’ bands:
•
<800-65535> – Specify a value from 800 -65535. The default is 1500.