Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 1279)

Brocade Mobility RFS Controller CLI Reference Guide 1271
53-1003098-01
27
data-rates 2.4GHz custom [1|11|12|18|2|24|36|48|5.5|54|6|9|basic-1|basic-11|
basic-12|basic-18|basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54 |
basic-6|basic-9|mcs0-15|mcs0-7|mcs8-15|basic-mcs0-7]
data-rates 5GHz [a-only|an|default]
data-rates 2.4GHz Configures the preset data rates for the 2.4 GHz frequency
Define both minimum Basic and optimal Supported rates as required for the 802.11b rates, 802.11g
rates and 802.11n rates supported by the 2.4 GHz band. These are the rates wireless client traffic is
supported within this mesh point.
If supporting 802.11n, select a supported MCS index. Set a Modulation and Coding Scheme (MCS) in
respect to the radio's channel width and guard interval. A MCS defines (based on RF channel conditions)
an optimal combination of 8 data rates, bonded channels, multiple spatial streams, different guard
intervals and modulation types. Mesh points can communicate as long as they support the same basic
MCS (as well as non-11n basic rates). The selected rates apply to associated client traffic within this
mesh point only.
custom
(1|11|12|18|2|24|36|
48|5.5|54|6|9|
basic-1|basic-11|
basic-12|basic-18|
basic-2|basic-24|
basic-36|basic-48|
basic-5.5|basic-54|
basic-6|basic-9|
mcs0-15|mcs0-7|
mcs8-15|basic-mcs0-7) Configures custom rates
•
1 – Configures the available rate at 1 Mbps
•
2 – Configures the available rate at 2 Mbps
•
5.5 – Configures the available rate at 5.5 Mbps
•
6 – Configures the available rate at 6 Mbps
•
9 – Configures the available rate at 9 Mbps
•
11 – Configures the available rate at 11 Mbps
•
12 – Configures the available rate at 12 Mbps
•
18 – Configures the available rate at 18 Mbps
•
24 – Configures the available rate at 24 Mbps
•
36 – Configures the available rate at 36 Mbps
•
48 – Configures the available rate at 48 Mbps
•
54 – Configures the available rate at 54 Mbps
•
basic-1 – Configures the available rate at a basic rate of 1 Mbps
•
basic-2 – Configures the available rate at a basic rate of 2 Mbps
•
basic-5.5 – Configures the available rate at a basic rate of 5.5 Mbps
•
basic-6 – Configures the available rate at a basic rate of 6 Mbps
•
basic-9 – Configures the available rate at a basic rate of 9 Mbps
•
basic-11 – Configures the available rate at a basic rate of 11 Mbps
•
basic-12 – Configures the available rate at a basic rate of 12 Mbps
•
basic-18 – Configures the available rate at a basic rate of 18 Mbps
•
basic-24 – Configures the available rate at a basic rate of 24 Mbps
•
basic-36 – Configures the available rate at a basic rate of 36 Mbps
•
basic-48 – Configures the available rate at a basic rate of 48 Mbps
•
basic-54 – Configures the available rate at a basic rate of 54 Mbps
•
basic-mcs0-7 – Configures the MCS index range of 0 - 7 for basic rate
•
mcs0-7 – Configures the MCS index range of 0-7 as the data rate
•
mcs0-15 – Configures the MCS index range of 0-15 as the data rate
•
msc8-15 – Configures the MCS index range of 8-15 as the data rate
Multiple choices can be made from the above list of rates
data-rates 5GHz Configures the preset data rates for the 5.0 GHz frequency
a-only Configures the data rate for the meshpoint using 802.11a only rates
bn Configures the data rate for the meshpoint using 802.11a and 802.11n rates
default Configures the data rate for the meshpoint at a pre-configured default rate for this frequency
g-only Configures the data rate for the meshpoint using 802.11g only rates
gn Configures the data rate for the meshpoint using 802.11g and 802.11n rates