Brocade Network Advisor SAN + IP User Manual v12.3.0 - Manual (Page 2578)

2506 Brocade Network Advisor SAN + IP User Manual
53-1003155-01
Views
I
left join SWITCH_PORT SWPORT on DEVICE_CONNECTION.SWITCH_PORT_ID = SWPORT.ID
left join SWITCH_PORT AGPORT on DEVICE_CONNECTION.AG_PORT_ID = AGPORT.ID
left join HBA_PORT_DEVICE_PORT_MAP on DEVICE_PORT.ID =
HBA_PORT_DEVICE_PORT_MAP.DEVICE_PORT_ID
left join HBA_PORT on HBA_PORT_DEVICE_PORT_MAP.HBA_PORT_ID =
HBA_PORT.DEVICE_PORT_ID
left join HBA on HBA_PORT.HBA_ID = HBA.ID
left join VM_FC_HBA_DEVICE_PORT_MAP ON
VM_FC_HBA_DEVICE_PORT_MAP.DEVICE_PORT_ID = DEVICE_PORT.ID
left join VM_FC_HBA ON VM_FC_HBA.ID = VM_FC_HBA_DEVICE_PORT_MAP.VM_FC_HBA_ID
left join VM_HOST ON VM_HOST.DEVICE_ENCLOSURE_ID = VM_FC_HBA.VM_HOST_ID
left join DEVICE_ENCLOSURE_MEMBER on DEVICE_PORT.ID =
DEVICE_ENCLOSURE_MEMBER.DEVICE_PORT_ID
left join DEVICE_NODE DN on DEVICE_PORT.NODE_ID = DN.ID
left join USER_DEFINED_DEVICE_DETAIL USERDEFINEDDETAILS on DN.WWN =
USERDEFINEDDETAILS.WWN;
EE_MONITOR_STATS_5MIN_INFO
create or replace view EE_MONITOR_STATS_5MIN_INFO as
select VIRTUAL_SWITCH.ID as VIRTUAL_SWITCH_ID,
ME_ID,
TARGET_ID as EE_MONITOR_ID,
timestamp with time zone 'epoch' + TIME_IN_SECONDS * interval '1 second' as
CREATION_TIME,
sum(case when MEASURE_ID = 208 then value else 0 end) as TX_UTILIZATION,
sum(case when MEASURE_ID = 209 then value else 0 end) as RX_UTILIZATION,
sum(case when MEASURE_ID = 210 then value else 0 end) as CRC_ERRORS
from TIME_SERIES_DATA_1, VIRTUAL_SWITCH
where ME_ID = MANAGED_ELEMENT_ID and COLLECTOR_ID = 16
group by ME_ID, TARGET_TYPE, TARGET_ID, TIME_IN_SECONDS,VIRTUAL_SWITCH_ID order
by TIME_IN_SECONDS desc;
EE_MONITOR_STATS_30MIN_INFO
create or replace view EE_MONITOR_STATS_30MIN_INFO as
select VIRTUAL_SWITCH.ID as VIRTUAL_SWITCH_ID,
ME_ID,
TARGET_ID as EE_MONITOR_ID,
timestamp with time zone 'epoch' + TIME_IN_SECONDS * interval '1 second' as
CREATION_TIME,
sum(case when MEASURE_ID = 208 then value else 0 end) as TX_UTILIZATION,
sum(case when MEASURE_ID = 209 then value else 0 end) as RX_UTILIZATION,
sum(case when MEASURE_ID = 210 then value else 0 end) as CRC_ERRORS
from TIME_SERIES_DATA_1_30MIN, VIRTUAL_SWITCH
where ME_ID = MANAGED_ELEMENT_ID and COLLECTOR_ID = 16
group by ME_ID, TARGET_TYPE, TARGET_ID, TIME_IN_SECONDS,VIRTUAL_SWITCH_ID order
by TIME_IN_SECONDS desc;
EE_MONITOR_STATS_2HOUR_INFO
create or replace view EE_MONITOR_STATS_2HOUR_INFO as
select VIRTUAL_SWITCH.ID as VIRTUAL_SWITCH_ID,
ME_ID,
TARGET_ID as EE_MONITOR_ID,