Delta RMC101 - Manual (Page 936)

RMC100 and RMCWin User Manual
Index-2
bookmarks .................................................. 107
event step table editor ................................ 108
overview ..................................................... 106
pasting addresses ...................................... 108
agency compliance ................................ 628, 630
Allen-Bradley .................................................. 261
ControlLogix ............................................... 208
Ethernet ...................................................... 208
PLC-5.......................................................... 208
RSView32 ................................................... 261
SLC 5/05 ..................................................... 208
SoftLogix 5 .................................................. 208
always on top ................................................. 108
Amp ................................................................ 447
Enable/Disable ........................................... 447
analog transducer ......... 360, 362, 364, 365, 584
auxiliary differential force control ................ 371
auxiliary pressure control............................ 370
configuration ............................................... 362
counts ......................................................... 584
differential force control .............................. 371
LED indicators ............................................ 364
overview ..................................................... 360
position control ........................................... 367
position reference ....................................... 367
pressure control .......................................... 370
pressure reference ..................................... 370
scaling......................................................... 365
specification ................................................ 365
velocity control ............................................ 368
velocity reference ....................................... 368
wiring .......................................................... 360
append cells ..................................................... 92
Curve Tool .................................................... 92
Arm Home ...................................................... 446
ARP ................................................................ 206
ASCII ..................................... 485, 506, 513, 633
commands ..................................485, 506, 513
table ............................................................ 633
At Pressure Window ....................................... 569
Auto Home Re-arm ....... 515, 527, 540, 549, 571
Auto Stop Bits ....... 525, 537, 547, 557, 569, 580
Automationdirect.com ............................ 218, 221
Avg Function .................................................. 441
AxesInPos Link Type ..................................... 616
Axis Initialized bit ............................................ 587
axis names ....................................................... 42
changing ....................................................... 42
axis select bits ........................................ 173, 175
Axis Status Word ............................................ 587
B
B Command ................................................... 470
B link type ....................................................... 624
Balluff ..................................................... 374, 409
digital MDT ................................................. 374
SSI ...................................................... 409, 411
Basic Link Type .............................................. 604
Bias Drive ....................................................... 470
Bidirectional Protocol ..................................... 337
Bits# OFF Link Type ...................................... 627
Bits# ON Link Type ........................................ 627
BitsOFF Link Type ......................................... 624
BitsON Link Type ........................................... 624
board file .................................................... 43, 44
changing between ........................................ 44
creating ......................................................... 43
editing ........................................................... 44
loading .......................................................... 44
saving ........................................................... 44
BOOTP .................................................. 198, 206
bridge ............................................................... 34
configuration ................................................. 34
overview ....................................................... 34
buttons ............................................................. 24
toolbar .......................................................... 24
C
c Command .................................................... 448
C Command ................................................... 447
C Link Type .................................................... 606
cable .............................................................. 387
quadrature with analog output.................... 387
calibration utility ............................................... 45
scale and offset ............................................ 45
camming .................................................. 76, 125
CAMP ............................................................. 206
Canadian UL .......................................... 628, 630
CE .......................................................... 628, 630
Change Acceleration ..................................... 447
Change Deceleration ..................................... 448
Changing Data from the Keyboard .................. 37
changing parameters on-the-fly ............. 469, 475
Check Wait Bits Link Type ............................. 621
Clear Integral Drive ........................................ 451
Clear Null Drive .............................................. 453
Clear Spline Segments .................................. 447
clockwise ........................................................ 631
Closed Loop Mode ......................................... 631
collisions ........................................................ 239
Ethernet ...................................................... 239
com ports ......................................................... 30
selecting ....................................................... 30
COM PROFIBUS ........................................... 305
Comm Trigger ................................................ 606
Comma Command ......................................... 441
Command ...................................................... 474
Command ...................................... 437, 453, 472
SoftPID Position Move ............................... 437
Command
mode .......................................................... 500
Command ...................................................... 500
Command
Acceleration................................................ 504