Lenze 8400 TopLine - Manual (Page 720)

10 Diagnostics & error management
10.9 Error messages of the operating system
720
Lenze · 8400 TopLine · Reference manual · DMS 6.0 EN · 06/2014 · TD05/TD14
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
CA0F: CAN control word [xx.0131.00015]
CE1: CAN RPDO1 [xx.0135.00001]
CE2: CAN RPDO2 [xx.0135.00002]
CE3: CAN RPDO3 [xx.0135.00003]
CP04: CAN RPDO4 [xx.0135.00004]
Response (Lenze setting printed in bold) Setting: C00594/1 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
Bit 14 ("SetFail") in the wCANControl control word of the
LS_DriveInterface system block has been set.
Trace back signal source on the CAN bus that sets bit 14
("SetFail").
Response (Lenze setting printed in bold) Setting: C00593/1 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
CAN on board : Time monitoring for RPDO1 has been
triggered.
• RPDO1 has not been received within the monitoring
time set in C00357/1 or was faulty.
• Set correct telegram length for CAN master
(transmitter).
• Eliminate electrical interference (e.g. EMC).
• Adjust monitoring time C00357/1 or switch off time
monitoring.
Response (Lenze setting printed in bold) Setting: C00593/2 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
CAN on board : Time monitoring for RPDO2 has been
triggered.
• RPDO2 has not been received within the monitoring
time set in C00357/2 or was faulty.
• Set correct telegram length for CAN master
(transmitter).
• Eliminate electrical interference (e.g. EMC).
• Adjust monitoring time C00357/2 or switch off time
monitoring.
Response (Lenze setting printed in bold) Setting: C00593/3 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
CAN on board : Time monitoring for RPDO3 has been
triggered.
• RPDO3 has not been received within the monitoring
time set in C00357/3 or was faulty.
• Set correct telegram length for CAN master
(transmitter).
• Eliminate electrical interference (e.g. EMC).
• Adjust monitoring time C00357/3 or switch off time
monitoring.
Response (Lenze setting printed in bold) Setting: C00593/4 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
CAN on board : Time monitoring for RPDO4 has been
triggered.
• RPDO4 has not been received within the monitoring
time set in C00357/4 or was faulty.
• Set correct telegram length for CAN master
(transmitter).
• Eliminate electrical interference (e.g. EMC).
• Adjust monitoring time C00357/4 or switch off time
monitoring.