Lenze 8400 TopLine - Manual (Page 1033)

Lenze · 8400 TopLine · Reference manual · DMS 6.0 EN · 06/2014 · TD05/TD14
1033
17 Parameter reference
17.2 Parameter list | C00621
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C00621/122 0: Not connected LS_ParReadWrite_6 : bReadWrite
Read/write request 6: Selection of reading/writing
C00621/123 0: Not connected LS_WriteParamList : bExecute
Writing the parameter list: Activate
C00621/124 0: Not connected LS_WriteParamList : bSelectWriteValue_1
Writing to parameter list: Selection of value set - 1
C00621/125 0: Not connected LS_WriteParamList : bSelectWriteValue_2
Writing to parameter list: Selection of value set - 2
C00621/126 0: Not connected LS_CANManagement : bResetNode
Reset CAN node
C00621/127 0: Not connected LS_CANManagement : bReInitCAN
Reinitialise CAN interface
C00621/128 0: Not connected LS_DigitalInput : bPosIn12_Load
Frequency input DI1/DI2: Load angle integrator with
starting value and reset status signal
C00621/147 0: Not connected LS_TouchProbe : bDisableTPDigIn3
TP input DI3: Disable TP function dynamically
C00621/148 0: Not connected LS_TouchProbe : bDisableTPDigIn4
TP input DI4: Disable TP function dynamically
C00621/149 0: Not connected LS_TouchProbe : bDisableTPDigIn5
TP input DI5: Disable TP function dynamically
C00621/150 0: Not connected LS_TouchProbe : bDisableTPDigIn6
TP input DI6: Disable TP function dynamically
C00621/151 0: Not connected LS_TouchProbe : bDisableTPDigIn7
TP input DI7: Disable TP function dynamically
C00621/152 0: Not connected LS_TouchProbe : bDisableTPDigIn3_Rising
TP input DI3: Disable recognition of rising edges
dynamically
C00621/153 0: Not connected LS_TouchProbe : bDisableTPDigIn3_Falling
TP input DI3: Disable recognition of falling edges
dynamically
C00621/154 0: Not connected LS_TouchProbe : bDisableTPDigIn4_Rising
TP input DI4: Disable recognition of rising edges
dynamically
C00621/155 0: Not connected LS_TouchProbe : bDisableTPDigIn4_Falling
TP input DI4: Disable recognition of falling edges
dynamically
C00621/156 0: Not connected LS_TouchProbe : bDisableTPDigIn5_Rising
TP input DI5: Disable recognition of rising edges
dynamically
C00621/157 0: Not connected LS_TouchProbe : bDisableTPDigIn5_Falling
TP input DI5: Disable recognition of falling edges
dynamically
C00621/158 0: Not connected LS_TouchProbe : bDisableTPDigIn3Window
TP input DI3: Enable acceptance window
C00621/159 0: Not connected LS_TouchProbe : bDisableTPDigIn4Window
TP input DI4: Enable acceptance window
C00621/160 0: Not connected LS_TouchProbe : bDisableTPDigIn5Window
TP input DI5: Enable acceptance window
C00621/161 0: Not connected LS_AxisBusIO : bSetFail
Set IO axis bus into the "error" status / IO data exchange
C00621/162 0: Not connected LS_AxisBusIO : bResetFail
IO axis bus: Reset "error" status
Parameter | Name:
C00621 | System connection list: Bool
Data type: UNSIGNED_16
Index: 23954
d
= 5D92
h