Lenze E94AxHE Servo Drives 9400 HighLine (Firmware 01-37) - Manual (Page 676)

9400 HighLine | Parameter setting & configuration
Index
676 Firmware 1.37 - 09/2006
L
Ref. deceleration time quick stop (C107) 554
Ref. for dec. time of stop (C2612) 629
Ref. mode (C2640) 631
Ref. speed 1 (C2644) 632
Ref. speed 2 (C2646) 632
Ref. S-ramp time (C2648) 632
Ref. torque limit (C2649) 633
Ref. touch probe configuration (C2651) 633
Reference search 165
Reference setting 165
Required license missing 493
Required safety module (C214) 565
Reset of error message 44 , 447
Resistor for spec. characteristic (C1192) 609
Resolution of a unit (C2532) 617
Resolver
Calculated acceleration unrealistic 473
Open circuit 471
Resolver - pole pair number (C80) 552
Resolver error correction (C416) 583
Resp. CAN life guarding error (C614) 595
Resp. DC bus overvoltage (C600) 592
Resp. to CAN bus off (C595) 591
Resp. to CAN heartbeat error (C613) 595
Resp. to CAN node guarding error (C612) 594
Resp. to CAN-RPDOx error (C591) 591
Resp. to comm. encoder error (C601) 593
Resp. to comm. error with MXI1 (C1501) 611
Resp. to comm. error with MXI2 (C1502) 612
Resp. to CPU temp. > C00126 (C589) 590
Resp. to device overload (C604) 593
Resp. to encoder open circuit (C580) 588
Resp. to external fault (C581) 588
Resp. to failure t. sensor motor (C594) 591
Resp. to heatsink fan failure (C610) 594
Resp. to heatsink temp. > C00122 (C582) 589
Resp. to imp. device config. (C615) 595
Resp. to integral fan failure (C611) 594
Resp. to limitation (C2716) 642
Resp. to max. motor current (C619) 596
Resp. to max. speed reached (C607) 593
Resp. to motor overload (C606) 593
Resp. to motor overtemp. KTY (C583) 589
Resp. to motor overtemp. PTC (C585) 589
Resp. to motor phase failure (C597) 592
Resp. to motor temp. > C00121 (C584) 589
Resp. to new firmware of drive (C635) 596
Resp. to new module in MXI1 (C636) 597
Resp. to new module in MXI2 (C637) 597
Resp. to open circuit AIN1 (C598) 592
Resp. to overload brake chopper (C573) 587
Resp. to resolver open circuit (C586) 590
Resp. to speed monitoring (C579) 588
Resp. to t. sensor drive failure (C588) 590
Resp.to overtemp. brake resist. (C574) 587
Resulting gearbox factors (C2531) 617
Rotor angle (C58) 549
Rotor position (C60) 549
Rr adaptation (C2860) 647
Run-time error 459
Runtime task 1 (C2121) 614
Runtime task 2 (C2122) 614
Runtime task 3 (C2123) 614
S
S1 torque characteristic I²xt mon. (C1196) 610
Safety engineering 135
Safety instructions 18
Safety module 135
Incompatible to setting under C00214 500
Safety module has been changed 453
Safety module has been removed 451
Safety module is defective or missing 450 , 452
Saturation characteristic 82
Saving of parameters failed 496
Service code (C100) 553
Service code (C1211) 611
Service code (C167) 559
Service code (C171) 559
Service code (C175) 560
Service code (C176) 560
Service code (C177) 561
Service code (C180) 561
Service code (C2850) 645
Service code (C2851) 645
Service code (C2852) 646
Service code (C2854) 646
Service code (C2856) 646
Service code (C2857) 647
Service code (C2858) 647
Service code (C2996) 647
Service code (C2997) 647
Service code (C2998) 647
Service code (C2999) 647
Service code (C308) 567
Service code (C309) 567
Service code (C310) 567
Service code (C325) 570
Service code (C326) 570
Service code (C327) 571
Service code (C328) 571
Service code (C329) 571
Service code (C330) 571
Service code (C335) 571
Service code (C336) 571
Service code (C337) 571