13 diagnostics & fault analysis, 7 error messages of the operating system 620 – Lenze 9400 User Manual
Page 620
13
Diagnostics & fault analysis
13.7
Error messages of the operating system
620
Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
8060963
Load encoder: Module selected in C00490 is not available
Fault
-
9437188
Loading of Lenze setting failed
Fault
-
6619136
Logbook: Overflow
Information
-
6619137
Logbook: Reset (read error)
Information
-
6619138
Logbook: Reset (version error)
Information
-
9502721
Mains voltage is switched off
Information
-
9502720
Mains voltage is switched on
Information
-
12058641
Maximum acceleration exceeded
Information
12058640
Maximum speed exceeded
Information
6815767
Memory module has been changed
Information or warning locked if
the hardware type has also
changed.
-
6815750
Memory module has been removed
System fault
-
6815746
Memory module is defective or missing
Fault
-
6815756
Memory module is defective or missing
System fault
-
6619139
Memory module is missing
Information
-
6815772
Memory module: Faulty file system
Fault
-
8126464
Memory module: file system has been formatted
Information
-
8126465
Memory module: File system has been restored
Information
-
12058627
Motor brake: Angular drift with closed brake too high
Quick stop by trouble
-
12058628
Motor brake: Autom. activated after waiting time has elapsed
Information
-
12058629
Motor brake: Status monitoring error
Quick stop by trouble
-
8060947
Motor control: Task overflow
System fault
-
8060931
Motor data are inconsistent
Information
-
8060951
Motor data are inconsistent
Information
-
8061004
Motor disconnected
No response
8060964
Motor encoder: Module selected in C00495 is not available
Fault
-
7864323
Motor load I²xt > C00120
Fault
-
7864322
Motor load I²xt > C00127
Warning
8060984
Motor parameter identification cancelled
Fault
-
8060965
Motor temperature: Module selected in C01193 is not available
Fault
-
8060958
Motor: Actual current value > C00620
Fault
8060960
Motor: Actual speed value > C00596
Fault
8060939
Motor: Calculated e.m.f. factor unrealistic
Information
-
8060941
Motor: Calculated flux factor unrealistic
Information
-
8060953
Motor: Calculated leakage inductance unrealistic
Information
-
8060929
Motor: Calculated motor impedance unrealistic
Information
-
8060930
Motor: Calculated mutual inductance unrealistic
Information
-
8060938
Motor: Calculated mutual inductance unrealistic
Information
-
8060937
Motor: Calculated rotor resistance unrealistic
Information
-
8060940
Motor: Calculated rotor time constant unrealistic
Information
-
8060934
Motor: Device current too low for rated magnetisation
Information
-
7798787
Motor: Overtemperature
Fault
8060932
Motor: Phase resistance too high
Information
-
7798799
Motor: PTC has triggered
No response
8060935
Motor: Rated current < rated magnetisation current
Information
-
7798786
Motor: Temperature > C00121
Warning
7798796
Motor: thermal detector is defective
Fault
9175063
MXI1: CAN module is missing or incompatible
Fault
9175059
MXI1: Digital frequency module is missing or incompatible
Fault
9175057
MXI1: Ethernet module is missing or incompatible
Fault
9175061
MXI1: ICM module is missing or incompatible
Fault
6815748
MXI1: Module changed during operation
Warning locked
-
hex
dec
Error message
Response (Lenze setting)
can be set in