13 diagnostics & fault analysis, 7 error messages of the operating system – Lenze 9400 User Manual
Page 617
Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06
617
13
Diagnostics & fault analysis
13.7
Error messages of the operating system
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
6881280
Code refresh
System fault
-
6815769
Combination MXI1/MXI2 not possible
System fault
-
6815775
Combination of memory module/device not possible
System fault
-
6815776
Combination of module in MXI1/device not possible
System fault
-
6815777
Combination of module in MXI2/device not possible
System fault
-
8323074
Communication error between device and device module
No response
9502734
Communication task: Standstill > 3 s
Fault
8323075
Communication with module in MXI1 interrupted
Information
-
8323076
Communication with module in MXI2 interrupted
Information
-
9568257
Communication with safety module interrupted
Information
-
9175066
ConnectTable active
Information
-
6815758
Control card incompatible
System fault
-
6815744
Control card is defective
System fault
-
6815752
Control card is defective
System fault
-
7864328
Control card is defective (UB18 neg.)
System fault
-
7864324
Control card is defective (UB24)
System fault
-
7864326
Control card is defective (UB8)
System fault
-
7864327
Control card is defective (VCC15 neg.)
System fault
-
7864325
Control card is defective (VCC15)
System fault
-
7864329
Control card is defective (VCC5)
System fault
-
7274496
Control card: Supply voltage (24 V DC) too low
Trouble
-
7667713
Controller enabled
Information
-
7667715
Controller in STO state
Information
-
8060999
Controller: Clamp operation
Information
-
8060981
Controller: Overload during acceleration phases
Fault
-
7667717
Controller: Pulse inhibit is active
Information
-
7798793
CPU: Overtemperature
Warning
-
7798792
CPU: Temperature > C00126
No response
7798798
CPU: thermal detector is defective
Fault
9502735
Cyclic task: Standstill > 60 s
Information
-
7798797
DC-bus capacitor: thermal detector is defective
Fault
8060942
DC-bus overvoltage
Trouble
8060943
DC-bus undervoltage
Trouble
-
12058637
Deceleration has been limited
Information
7864321
Device utilisation Ixt > 100 %
Fault
-
7864320
Device utilisation Ixt > C00123
Warning
10027011
DFIN (MXI1): Signal error enable/lamp control
Warning
C13041
10027012
DFIN (MXI1): Supply cannot be corrected anymore
Warning
C13042
10027008
DFIN (MXI1): Track error A-/A
Fault
C13040
10027009
DFIN (MXI1): Track error B-/B
Fault
C13040
10027010
DFIN (MXI1): Track error Z-/Z
Fault
C13040
11141123
DFIN (MXI2): Signal error enable/lamp control
Warning
C14041
11141124
DFIN (MXI2): Supply cannot be corrected anymore
Warning
C14042
11141120
DFIN (MXI2): Track error A-/A
Fault
C14040
11141121
DFIN (MXI2): Track error B-/B
Fault
C14040
11141122
DFIN (MXI2): Track error Z-/Z
Fault
C14040
10027013
DFOUT (MXI1): Maximum frequency reached
Warning
C13080
11141125
DFOUT (MXI2): Maximum frequency reached
Warning
C14080
9437196
Disconnection in the case of par. storage
Fault
-
6946833
Division by zero
Fault
-
8060945
Earth fault detected
Fault
-
6815773
Electronic nameplate: Checksum error
Warning
-
hex
dec
Error message
Response (Lenze setting)
can be set in