Lenze 8400 - Manual (Page 1489)

Lenze · 8400 protec HighLine · Reference manual · DMS 3.0 EN · 03/2013 · TD05
1489
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
PSM
Activate Lss sat. char. (C02859) 1065
Imax Lss saturation characteristic (C02855) 1065
Lss saturation characteristic (C02853) 1065
Maximum motor current field weakening (C00938) 952
PTC 285
Q
Quick stop setting (C00104) 764
R
Ramp function generator (L_DFRFG) 1254
Rated device current (C00098) 762
Rated motor current (C00088) 760
Rated motor frequency (C00089) 760
Rated motor power (C00081) 759
Rated motor speed (C00087) 760
Rated motor torque (C00097) 762
Rated motor voltage (C00090) 761
Rated power - brake resistor (C00130) 768
Reduc. brake chopper threshold (C00174) 785
Reference project 1153
Reference setting 489
Referencing mode 491
Remote
Acceleration/deceleration time (C00461) 831
Control (C00462) 831
MCK control (C00463) 832
Monitoring timeout (C00464) 833
Setpoint selection (C00729) 889
Remote control
Activate/exit 1441
Assign control functions 1439
Reset error message 584
Reset node (CAN) 636
Reset reference information 449
Reset time Imax/M controller (C00074) 757
Resp. to brake resist. overtemp. (C00574) 848
Resp. to brake resist. overtemp. PTC (C00587) 851
Resp. to CAN bus connection (C00592) 852
Resp. to CANx_IN monitoring (C00593) 853
Resp. to communication error with MCI (C01501) 1018
Resp. to control word error (C00594) 853
Resp. to controller limitations (C00570) 848
Resp. to DC-bus voltage (C00600) 856
Resp. to earth fault (C00602) 856
Resp. to encoder open circuit HTL (C00586) 851
Resp. to fan failure (C00566) 847
Resp. to heatsink temp. > shutdown temp. -5°C (C00582) 850
Resp. to I/O monitoring (C00598) 855
Resp. to LS_SetError_x (C00581) 850
Resp. to mains phase failure (C00565) 846
Resp. to max. freq. feedb. DIG12/56 (C00607) 857
Resp. to max. speed at switching freq. (C00588) 851
Resp. to max. speed/output freq. reached (C00579) 849
Resp. to maximum current (C00609) 857
Resp. to maximum torque (C00608) 857
Resp. to motor overload (I²xt) (C00606) 856
Resp. to motor overtemp. PTC (C00585) 851
Resp. to motor phase failure (C00597) 855
Resp. to operating system error (C00580) 850
Resp. to peak current (C00569) 847
Resp. to PLI monitoring (C00643) 870
Resp. to speed controller limited (C00567) 847
Resp. to switching frequency reduction (C00590) 852
Resp. to too frequent AutoFailReset (C00189) 788
Retracting from limit switches 512
Reversing the phase sequence 256
Rotary table application 470
Rotor displacement angle detection after controller enable 214
RPDO1 communication parameter (I-1400) 688
RPDO1 mapping parameter (I-1600) 691
RPDO2 communication parameter (I-1401) 689
RPDO2 mapping parameter (I-1601) 692
RPDO3 communication parameter (I-1402) 690
RPDO3 mapping parameter (I-1602) 692
Running time (C00180) 786
S
S_ShapingActive (status bit) 450
Safe stop 1 453
Safety engineering 709
Safety functions 453
Safety instructions 25
Safety module 453
Safety on board 709
Safety option 709
Safety system (status LEDs) 554
Saturation characteristic 212
SC
Depth of current setpoint filter (C00272) 799
Field feedforward control (C00576) 849
Filter time const. DC detection (C00280) 800
Freq. current setpoint filter (C00270) 798
Max. acceleration change (C00274) 799
max. output voltage (C00276) 800
Settings (C00079) 758
Start motor magnetising current (C00918) 951
Tdn speed controller (C00072) 756
Tn field controller (C00078) 758
Tn field weakening controller (C00578) 849
Vp field controller (C00077) 758
Vp field weakening controller (C00577) 849
Width of current setpoint filter (C00271) 799
Scaling of physical units 1108
Sd10
Speed limit for feedback system 12 (error message) 597