Lenze 8400 - Manual (Page 1479)

Lenze · 8400 protec HighLine · Reference manual · DMS 3.0 EN · 03/2013 · TD05
1479
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Flying restart function 245
Activation (C00990) 961
Current (C00994) 962
Integration time (C00993) 962
Process (C00991) 962
Start frequency (C00992) 962
Following error 481
Following error monitoring system 481
Format error 670
FreqIn12
Function (C02844) 1064
PosIn comparison value (C02845) 1064
FreqInxx
Gain (C02843) 1064
Offset (C02842) 1063
FreqInxx_dnOut_p (C00449) 830
FreqInxx_nOut_a (C00446) 829
FreqInxx_nOut_v (C00445) 828
Frequency limitation (C00910) 950
Function block editor 1102
Function block interconnection 30
Function blocks 1154
Function L_Counter 1-3 (C01100) 988
Function library 1154
G
Gearbox ratio 468
General data (CAN on board) 631
General purpose functions 431
GP functions (GeneralPurpose) 431
H
Hardware limit switch 476
Heartbeat protocol 672
Heatsink temperature (C00061) 755
Holding brake
Activation time (C02593) 1055
Operating mode (C02580) 1052
Setting (C02582) 1053
Speed thresholds (C02581) 1053
Status (C02607) 1056
Time system (C02589) 1055
Holding brake control 535
Homing 489
Homing on the fly 504
HomPosAvailable (status bit) 449
I
I-1000 679
I-1001 679
I-1003 680
I-1005 681
I-1006 682
I-1014 682
I-1016 683
I-1017 684
I-1018 684
I-1200 685
I-1201 686
I-1400 688
I-1401 689
I-1402 690
I-1600 691
I-1601 692
I-1602 692
I-1800 693
I-1801 695
I-1802 696
I-1A00 697
I-1A01 697
I-1A02 698
Id1
Motor data identification error (error message) 594
Id3
CINH identification (error message) 594
Id4
Resistor identification error (error message) 594
Id7
Motor control does not match motor data (error message)
595
Identification procedure (C02867) 1067
Identifier (CAN) 637
Identifiers of the parameter data objects 659
Identifiers of the process data objects 652
Identity (C00219) 792
Identity object (I-1018) 684
Imax controller 153
Imax in generator mode (C00023) 749
Imax in motor mode (C00022) 749
Imax/M controller gain (C00073) 757
Inching mode 505
Initial value motor overload (I²xt) (C00122) 767
Insert options for copied elements 1145
Inserting complete interconnection from reference project
1153
Inserting copied elements 1145
Inserting FB interconnection from reference project 1153
Integrated error detection 670
Internal control signals (C00138) 771
Inversion of gearbox stages (C01067) 976
Inverter motor brake 273
nAdd (C00987) 961
PT1 filter time (C00988) 961
Io11
DigOut level (error message) 598
J
Jerk limitation 522