Lenze 8400 - Manual (Page 1488)

Index
1488
Lenze · 8400 protec HighLine · Reference manual · DMS 3.0 EN · 03/2013 · TD05
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Positioning 513
Speed follower 487
StandBy 452
Stop 528
Operating mode change with profile number 463
Operation with safety module 453
Optical location 107
Optimising the response to setpoint changes (SC) 233
Optimising the response to setpoint changes (SLVC) 193
Option "Lock bFail at TroubleQSP" 124
Original application|control source (C00008) 744
oS1
Maximum speed limit reached (error message) 593
oS2
Max. motor speed (error message) 594
Oscillation damping 253
Oscillation damping filter time (C00235) 795
Oscillation damping influence (C00234) 795
Oscilloscope function 613
ot1
Maximum torque reached (error message) 591
ot2
Speed controller output limited (error message) 596
OU
DC bus overvoltage (error message) 592
Output frequency (C00058) 754
Output power (C00980) 960
Overchange 519
Override 531
Override point of field weakening (C00080) 759
P
Parameter change-over 718
Parameterisable function blocks 1105
Password data (C00505) 843
Password protection 42
PC manual control 86
PDO mapping 646
,
647
,
648
PDO synchronisation 655
Peak current limitation 145
Phase sequence reversal 256
Plant parameters 133
PLI without motion
Adaptation of ident angle (C02875) 1069
Adaptation of time duration (C02872) 1068
Ident. el. rotor displ. angle (C02873) 1068
Optimisation factor (C02870) 1068
Running time (C02871) 1068
PLI without motion (C02874) 1069
Pole position identification 214
Port block "LP_CanIn1" 646
Port block "LP_CanIn2" 647
Port block "LP_CanIn3" 648
Port block "LP_CanOut1" 649
Port block "LP_CanOut2" 650
Port block "LP_CanOut3" 651
PosExecute (control bit) 462
PosExecute control bit 462
PosFollower
Setting (C01218) 998
Position control 269
Position encoder selection (C00490) 842
Position follower 529
Position teaching 527
Positioning 513
Positioning modes 520
Power section ID (C00093) 761
Power-on time meter (C00179) 786
Pre-defined error field (I-1003) 680
Printing the interconnection 1148
Process data objects, identifiers 652
Processing time 632
Producer heartbeat time (I-1017) 684
Product type code (C00203) 791
PROFIBUS 700
Profile data
Acceleration (C01303) 1015
Deceleration (C01304) 1016
Final speed (C01305) 1016
Position (C01301) 1015
Positioning mode (C01300) 1014
Sequence profile (C01307) 1017
Speed (C01302) 1015
S-ramp time (C01306) 1016
TP profile (C01308) 1017
TP signal source (C01309) 1017
Profile entry 517
Profile generator (L_DFRFG) 1254
Profile linkage with velocity changeover (overchange) 519
PROFINET 700
PS01
No memory module (error message) 601
PS02
Par. set invalid (error message) 602
PS03
Par. set device invalid (error message) 602
PS04
Par. set Mci invalid (error message) 602
PS07
Par. memory module invalid (error message) 602
PS08
Par. device invalid (error message) 603
PS09
Par. format invalid (error message) 603
PS10
Memory module binding invalid (error message) 603