Index – Lenze E94AxPExxxx User Manual
Page 969
Lenze · 9400 Servo PLC· Reference manual · DMS 4.0 EN · 11/2013 · TD05/06
969
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Module is missing or incompatible (error message)
PROFIBUS module is missing or incompatible (error message)
Wrong module (error message)
N
Negative direction of rotation limited (error message)
Negative limit switch has triggered (error message)
Negative software limit switch overtravelled (error message)
Network management telegram (NMT)
New application loaded (error message)
NMT (network management)
No heartbeat signal detected (error message)
No parameters for module in MXI1 (error message)
No parameters for module in MXI2 (error message)
No. of CRC cycles (C00618)
Node address
Node guarding event
Node guarding protocol
Node ID
Node life time
Number Of Cam Data Points (C02922)
Number Of Cam Tracks (C02919)
Number Of Cont Data Points (C02942)
Number Of Cont Tracks (C02939)
Number of encoder increments (C00420)
Number of Pos Data Points (C02962)
Number of Pos Tracks (C02959)
O
observation software limit positions (C02720)
Offset actual pos. value/setp. (C02578)
Online change mode
Online Change Mode (C02905)
Online Change State (C02906)
Operating mode (C02770)
Operating mode brake (C02580)
Operation with increased continuous power
Optimising response to setpoint changes
Overcurrent detected (error message)
Overload
P
Parameter error information (C217)
Parameter set
Type of standard device has been changed (error message)
Version conflict (error message)
Parameter set faulty (error message)
Parameter set loaded (error message)
Parameter set restored (error message)
Parameter set saved (error message)
Parameter set switching
Parameter sets
Password entry
Password for cam data
PDO delay
PDO mapping (MXI1)
Faulty configuration (error message)
PDO mapping (MXI2)
Faulty configuration (error message)
PDO synchronisation
Permissible angle of rotation (C02595)
Permissible direction of rot. (C02707)
PF_dnMotorAcc_x (C02685)
PF_dnPositionSet_p (C02688)
PF_dnSpeedAdd1_s (C02686)
PF_PositionFollower
Phase controller gain (C00254)
Phase controller output (C02557)
Phase currents (C00055)
Plant parameters
PLC configuration invalid (error message)
PLC functionality
PLI 360° absolute current amplitude (C00645)
PLI 360° current amplitude (C00641)
PLI 360° traversing direction (C00643)
PLI min. motion absolute cur. amp. (C00651)
PLI min. mov. reset time (C00649)
PLI min.mov. curr. amplitude (C00646)
Pointer access in impermissible memory area (error message)
Pole position (C00058)
Pole position identification
,
Pole position recognition cancelled (error message)
PolePosId 360° fault tol. (C00644)
PolePosId 360° ramp time (C00642)
PolePosId min.mov. cur.rise rate (C00647)
PolePosId min.mov. gain (C00648)
PolePosId min.mov. max.perm.mov. (C00650)
PolePosition setpoint (C02788)
PolePositionIdentification
Dig. signals (C02789)
Pos Data Point Choice (C02963)
Pos Track Choice (C02960)
Pos. contr. limitation (C02556)
Pos. contr. output (C02558)
POS_dnProfileSpeed_s (C02676)
POS_dnState (C02675)
POS_dwActualProfileNumber (C02674)
POS_Positioner
Position control structure (C02570)
Position controller gain (C02553)
Position controller reset time (C02554)
Position encoder
Module selected in C00490 not available (error message)