Index – Lenze E94AxPExxxx User Manual
Page 968
Index
968
Lenze · 9400 Servo PLC· Reference manual · DMS 4.0 EN · 11/2013 · TD05/06
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Min. S-ramp time (C02706)
Minimum brake resistance (C00134)
MM440
Modulation modes
MOL_dnState (C02780)
MOL_SetpointCurrent (C02779)
Moment of inertia (C00273)
Monitoring
Monitoring of limit positions
Mot. overload protection (I²xt) (C00120)
Mot. overload warning threshold (C00127)
Motor
Actual current value > C00620 (error message)
Actual speed value > C00596 (error message)
Calculated e.m.f. factor unrealistic (error message)
Calculated flux factor unrealistic (error message)
Calculated leakage inductance unrealistic (error message)
Calculated motor impedance unrealistic (error message)
Calculated mutual inductance unrealistic (error message)
Calculated rotor resistance unrealistic (error message)
Calculated rotor time constant unrealistic (error message)
Device current too low for rated magnetisation (error
message)
Overtemperature (error message)
Phase resistance too high (error message)
PTC has triggered (error message)
Rated current < rated magnetising current (error message)
Temperature > C00121 (error message)
Thermal detector is defect (error message)
Motor - magnetising current (C00092)
Motor - mutual inductance (C00079)
Motor - number of pole pairs (C00059)
Motor brake
Angular drift with closed brake too high (error message)
Motor brake
Autom. activated after waiting time has elapsed (error
message)
Status monitoring error (error message)
Motor control
Task overflow (error message)
Motor cosine phi (C00091)
Motor current (C00054)
Motor data are inconsistent (error message)
Motor encoder
Module selected in C00495 not available (error message)
Motor encoder selection (C00495)
Motor holding brake
Motor holding brake control module E94AZHA0051
Motor holding brake control module E94AZHX0051
Motor interface
% signals (C02568)
Dig. signals (C02569)
Motor load I²xt > C00120 (error message)
Motor load I²xt > C00127 (error message)
Motor mounting direction (C02527)
Motor operating temperature (C01194)
Motor parameter identification was cancelled (error message)
Motor phase failure
Motor phase failure monitoring
Motor phase failure threshold (C00599)
Motor phase failure volt. threshold (C02867)
Motor protection
Motor reference speed
Motor reference speed (C00011)
Motor rotor resistance (C00082)
Motor rotor time constant (C00083)
Motor speed
Motor standstill time constant (C00494)
Motor stator leakage inductance (C00085)
Motor stator resistance (C00084)
Motor switched off (error message)
Motor temp. feedback system (C01193)
Motor temperature
Module selected in C01193 not available (error message)
Motor temperature (C00063)
Motor temperature monitoring (PTC)
Motor thermal sensor (C01190)
Motor voltage (C00052)
Multiturn resolution (C02761)
MXI1
CAN module is missing or incompatible (error message)
Digital frequency module is missing or incompatible (error
message)
Ethernet module is missing or incompatible (error message)
ICM module is missing or incompatible (error message)
Module changed during operation (error message)
Module has been changed (error message)
Module is defect or missing (error message)
Module is missing or incompatible (error message)
PROFIBUS module is missing or incompatible (error message)
Wrong module (error message)
MXI2
CAN module is missing or incompatible (error message)
Digital frequency module is missing or incompatible (error
message)
Ethernet module is missing or incompatible (error message)
ICM module is missing or incompatible (error message)
Module changed during operation (error message)
Module has been changed (error message)
Module is defect or missing (error message)