Brocade Multi-Service IronWare Multiprotocol Label Switch (MPLS) Configuration Guide (Supporting R05.6.00) - Manual (Page 628)

Brocade(config-mpls)# show isis database mu1.00-00 detail
IS-IS Level-2 Link State Database
LSPID Seq Num Checksum Holdtime ATT/P/OL
mu1.00-00* 0x00000010 0xd938 35 1/0/0
Area Address: 47
NLPID: IPv6 IP
Hostname: mu1
TE Router ID: 10.1.1.1
Metric: 10 IP-Extended 10.1.1.0/24 Up: 0 Subtlv: 0
Metric: 10 IP-Extended 10.2.1.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.2.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.3.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.4.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.5.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.6.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.7.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.8.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.9.0/24 Up: 0 Subtlv: 0
Metric: 1 IP-Extended 10.1.10.0/24 Up: 0 Subtlv: 0
Metric: 10 IP-Extended 10.1.0.0/16 Up: 0 Subtlv: 0
Metric: 10 IPv6 Reachability 1000::/32 Up: 0 Subtlv: 0
Metric: 10 IPv6 Reachability 2000::/32 Up: 0 Subtlv: 0
Metric: 10 IS-Extended mu1.02
Admin Group: 0x00000000
Interface IP Address: 10.1.1.1
Link BW: 10000000 kbits/sec
Reservable BW: 10000000 kbits/sec
Unreserved BW:
[0] 10000000 kbits/sec [1] 10000000 kbits/sec
[2] 10000000 kbits/sec [3] 10000000 kbits/sec
[4] 10000000 kbits/sec [5] 10000000 kbits/sec
[6] 10000000 kbits/sec [7] 10000000 kbits/sec
Admin Group: 0x00000000
Interface IP Address: 10.1.1.1
Neighbor IP Address: 10.1.1.2
Link BW: 10000000 kbits/sec
Reservable BW: 8000000 kbits/sec
Unreserved BW:
[0] 8000000 kbits/sec [1] 8000000 kbits/sec
[2] 8000000 kbits/sec [3] 8000000 kbits/sec
[4] 8000000 kbits/sec [5] 8000000 kbits/sec
[6] 8000000 kbits/sec [7] 8000000 kbits/sec
Metric: 10 IS-Extended mu3.00
604 Multi-Service IronWare Multiprotocol Label Switch (MPLS) Configuration Guide
53-1003031-02
IS-IS shortcuts
5
Clearing IS-IS shortcuts
When the user clears IS-IS shortcuts, IS-IS attempts to remap the LSP To address to IS-IS system
ID. Clearing shortcuts is useful when the mapping between the To address and System ID must be
refreshed once the LSP tunnel is being used in the SPF calculation.
NOTE
This is not a common operation.
To clear IS-IS shortcuts from the configuration, use one of the following CLI commands at any level
of the CLI:
• clear isis shortcut – This command clears all IS-IS shortcuts from the configuration.