Directory

Brands

PLANET manuals

Routers

XGS3-24040

Manual

PLANET XGS3-24040 User Manual

Command guide, Slot layer 3 ipv6/ipv4 routing chassis switch

Text mode
Original mode

PLANET XGS3-24040 User Manual | 869 pages

PLANET XGS3-24040 User Manual | 869 pages

Pages: 1 2 3 4 5 6 7 … 869

wrong Brand
wrong Model
non readable

Table of contents

Document Outline

Chapter 1 Commands for Basic Switch Configuration
- 1.1 Commands for Basic Configuration
- 1.2 Commands for Telnet
- 1.3 Commands for Configuring Switch IP
- 1.4 Commands for SNMP
- 1.5 Commands for Switch Upgrade
Chapter 2 File System Commands
- 2.1 cd
- 2.2 copy
- 2.3 delete
- 2.4 dir
- 2.5 format
- 2.6 mkdir
- 2.7 mount
- 2.8 pwd
- 2.9 rename
- 2.10 rmdir
- 2.11 unmount
Chapter 3 Commands for Cluster
- 3.1 clear cluster nodes
- 3.2 cluster auto-add
- 3.3 cluster commander
- 3.4 cluster ip-pool
- 3.5 cluster keepalive interval
- 3.6 cluster keepalive loss-count
- 3.7 cluster member
- 3.8 cluster member auto-to-user
- 3.9 cluster reset member
- 3.10 cluster run
- 3.11 cluster update member
- 3.12 debug cluster
- 3.13 debug cluster packets
- 3.14 show cluster
- 3.15 show cluster members
- 3.16 show cluster candidates
- 3.17 show cluster topology
- 3.18 rcommand commander
- 3.19 rcommand member
Chapter 4 Commands for Network Port Configuration
- 4.1 Commands for Ethernet Port Configuration
Chapter 5 Commands for Port Isolation Function
- 5.1 isolate-port group
- 5.2 isolate-port group switchport interface
- 5.3 isolate-port apply
- 5.4 show isolate-port group
Chapter 6 Commands for Port Loopback Detection Function
- 6.1 loopback-detection control
- 6.2 loopback-detection specified-vlan
- 6.3 loopback-detection interval-time
- 6.4 loopback-detection control-recovery timeout
- 6.5 show loopback-detection
- 6.6 debug loopback-detection
Chapter 7 Commands for ULDP
- 7.1 uldp enable
- 7.2 uldp disable
- 7.3 uldp hello-interval
- 7.4 uldp aggressive-mode
- 7.5 uldp manual-shutdown
- 7.6 uldp reset
- 7.7 uldp recovery-time
- 7.8 show uldp
- 7.9 debug uldp fsm interface ethernet
- 7.10 debug uldp error
- 7.11 debug uldp event
- 7.12 debug uldp packet
- 7.13 debug uldp interface ethernet
Chapter 8 Commands for LLDP Function
- 8.1 lldp enable
- 8.2 lldp enable (Port)
- 8.3 lldp mode
- 8.4 lldp tx-interval
- 8.5 lldp msgTxHold
- 8.6 lldp transmit delay
- 8.7 lldp notification interval
- 8.8 lldp trap
- 8.9 lldp transmit optional tlv
- 8.10 lldp neighbors max-num
- 8.11 lldp tooManyNeighbors
- 8.12 show lldp
- 8.13 show lldp traffic
- 8.14 show lldp interface ethernet
- 8.15 show lldp neighbors interface ethernet
- 8.16 show debugging lldp
- 8.17 debug lldp
- 8.18 debug lldp packets
- 8.19 clear lldp remote-table
Chapter 9 Commands for Port Channel
- 9.1 debug port-channel
- 9.2 interface port-channel
- 9.3 lacp port-priority
- 9.4 lacp system-priority
- 9.5 load-balance
- 9.6 port-group
- 9.7 port-group mode
- 9.8 show port-group
Chapter 10 Commands for Jumbo
- 10.1 jumbo enable
Chapter 11 VLAN Configuration
- 11.1 Commands for VLAN Configuration
- 11.2 Commands for Dynamic VLAN Configuration
- 11.3 Commands for Voice VLAN Configuration
Chapter 12 Commands for MAC Address Table Configuration
- 12.1 Commands for MAC Address Table Configuration
- 12.2 Commands for Mac Address Binding configuration
Chapter 13 ommands for MSTP
- 13.1 Commands for MSTP
- 13.2 Commands for Monitor and Debug
Chapter 14 Commands for QoS and PBR
- 14.1 class
- 14.2 class-map
- 14.3 match
- 14.4 mls qos
- 14.5 mls qos cos
- 14.6 mls qos aggregate-policy
- 14.7 mls qos trust
- 14.8 priority-queue out
- 14.9 queue bandwidth
- 14.10 set
- 14.11 service-policy
- 14.12 show class-map
- 14.13 show policy-map
- 14.14 show mls qos aggregate-policy
- 14.15 show mls qos interface
- 14.16 show mls qos maps
- 14.17 show mls-qos
- 14.18 wrr-queue bandwidth
- 14.19 wrr-queue cos-map
Chapter 15 Commands for IPv6 PBR
- 15.1 class
- 15.2 class-map
- 15.3 mls qos
- 15.4 match ipv6 access-group
- 15.5 policy-map
- 15.6 set
- 15.7 service-policy
Chapter 16 Commands for Flow-based Redirection
- 16.1 access-group redirect to interface ethernet
- 16.2 show flow-based-redirect
Chapter 17 Commands for Layer 3 Forwarding
- 17.1 Commands for Layer 3 Interface
- 17.2 Commands for IPv4/v6 configuration
- 17.3 Commands for IP Route Aggregation
  - 17.3.1 ip fib optimize
- 17.4 Commands for URPF
- 17.5 Commands for ARP Configuration
Chapter 18 Commands for ARP Scanning Prevention
- 18.1 anti-arpscan enable
- 18.2 anti-arpscan port-based threshold
- 18.3 anti-arpscan ip-based threshold
- 18.4 anti-arpscan trust
- 18.5 anti-arpscan trust ip
- 18.6 anti-arpscan recovery enable
- 18.7 anti-arpscan recovery time
- 18.8 anti-arpscan log enable
- 18.9 anti-arpscan trap enable
- 18.10 show anti-arpscan
- 18.11 debug anti-arpscan
Chapter 19 Commands for Preventing ARP, ND Spoofing
- 19.1 ip arp-security updateprotect
- 19.2 ipv6 nd-security updateprotect
- 19.3 ip arp-security learnprotect
- 19.4 ipv6 nd-security learnprotect
- 19.5 ip arp-security convert
- 19.6 ipv6 nd-security convert
- 19.7 clear ip arp dynamic
- 19.8 clear ipv6 nd dynamic
Chapter 20 Command for ARP GUARD
- 20.1 arp-guard ip
Chapter 21 Command for ARP Local Proxy
- 21.1 ip local proxy-arp
Chapter 22 Commands for Gratuitous ARP Configuration
- 22.1 ip gratuitous-arp
- 22.2 show ip gratuitous-arp
Chapter 23 Commands for ND Snooping
- 23.1 clear ipv6 nd snooping binding
- 23.2 debug ipv6 nd snooping
- 23.3 ipv6 nd snooping enable (Global mode)
- 23.4 ipv6 nd snooping mac-binding-limit
- 23.5 ipv6 nd snooping max-dad-delay
- 23.6 ipv6 nd snooping max-dad-prepare-delay
- 23.7 ipv6 nd snooping max-sac-lifetime
- 23.8 ipv6 nd snooping policy
- 23.9 ipv6 nd snooping port-binding-limit
- 23.10 ipv6 nd snooping static-binding
- 23.11 ipv6 nd snooping trust
- 23.12 ipv6 nd snooping user-control
- 23.13 show ipv6 nd snooping
- 23.14 show ipv6 nd snooping mac-binding
Chapter 24 Commands for DHCP
- 24.1 Commands for DHCP Server Configuration
- 24.2 Commands for DHCP Relay Configuration
  - 24.2.1 ip forward-protocol udp bootps
  - 24.2.2 ip helper-address
Chapter 25 Commands for DHCPv6
- 25.1 clear ipv6 dhcp binding
- 25.2 clear ipv6 dhcp server statistics
- 25.3 debug ipv6 dhcp client packet
- 25.4 debug ipv6 dhcp detail
- 25.5 debug ipv6 dhcp relay packet
- 25.6 debug ipv6 dhcp server
- 25.7 dns-server
- 25.8 domain-name
- 25.9 excluded-address
- 25.10 ipv6 address
- 25.11 ipv6 dhcp client pd
- 25.12 ipv6 dhcp client pd hint
- 25.13 ipv6 dhcp pool
- 25.14 ipv6 dhcp relay destination
- 25.15 ipv6 dhcp server
- 25.16 ipv6 general-prefix
- 25.17 ipv6 local pool
- 25.18 lifetime
- 25.19 network-address
- 25.20 prefix-delegation
- 25.21 prefix-delegation pool
- 25.22 service dhcpv6
- 25.23 show ipv6 dhcp
- 25.24 show ipv6 dhcp binding
- 25.25 show ipv6 dhcp interface
- 25.26 show ipv6 dhcp local pool
- 25.27 show ipv6 dhcp pool
- 25.28 show ipv6 dhcp statistics
- 25.29 show ipv6 general-prefix
Chapter 26 Commands for DHCP Option 82
- 26.1 ip dhcp relay information option
- 26.2 ip dhcp relay information policy
- 26.3 ip dhcp relay information option subscriber-id
- 26.4 ip dhcp server relay information enable
- 26.5 show ip dhcp relay information option
- 26.6 debug ip dhcp relay packet
Chapter 27 Commands for DHCP Snooping
- 27.1 debug ip dhcp snooping packet interface
- 27.2 debug ip dhcp snooping packet
- 27.3 debug ip dhcp snooping update
- 27.4 debug ip dhcp snooping event
- 27.5 debug ip dhcp snooping binding
- 27.6 ip dhcp snooping
- 27.7 ip dhcp snooping binding
- 27.8 ip dhcp snooping binding user
- 27.9 ip dhcp snooping binding arp
- 27.10 ip dhcp snooping binding dot1x
- 27.11 ip dhcp snooping binding user-control
- 27.12 ip dhcp snooping binding user-control max-user
- 27.13 ip dhcp snooping trust
- 27.14 ip dhcp snooping action
- 27.15 ip dhcp snooping action MaxNum
- 27.16 ip dhcp snooping limit-rate
- 27.17 ip dhcp snooping information enable
- 27.18 ip dhcp snooping option82 enable
- 27.19 enable trustview key
- 27.20 ip user helper-address
- 27.21 show trustview status
- 27.22 show ip dhcp snooping
Chapter 28 Commands for DHCPv6 Snooping
- 28.1 clear ipv6 dhcp snooping binding
- 28.2 debug ipv6 dhcp snooping binding
- 28.3 debug ipv6 dhcp snooping event
- 28.4 debug ipv6 dhcp snooping packet
- 28.5 ipv6 dhcp snooping action
- 28.6 ipv6 dhcp snooping action MaxNum
- 28.7 ipv6 dhcp snooping binding enable
- 28.8 ipv6 dhcp snooping binding nd
- 28.9 ipv6 dhcp snooping binding user
- 28.10 ipv6 dhcp snooping binding user-control
- 28.11 ipv6 dhcp snooping binding-limit
- 28.12 ipv6 dhcp snooping enable
- 28.13 ip dhcp snooping trust
- 28.14 show ipv6 dhcp snooping
- 28.15 show ipv6 dhcp snooping binding
- 28.16 show ipv6 dhcp snooping interface
Chapter 29 Commands for Routing Policy
- 29.1 ip prefix-list description
- 29.2 ip prefix-list seq
- 29.3 ip prefix-list sequence-number
- 29.4 match as-path
- 29.5 match community
- 29.6 match interface
- 29.7 match ip
- 29.8 match ipv6 address
- 29.9 match ipv6 next-hop
- 29.10 match metric
- 29.11 match origin
- 29.12 match route-type
- 29.13 match tag
- 29.14 route-map
- 29.15 set aggregator
- 29.16 set as-path
- 29.17 set atomic-aggregate
- 29.18 set comm-list
- 29.19 set community
- 29.20 set extcommunity
- 29.21 set ip next-hop
- 29.22 set local-preference
- 29.23 set metric
- 29.24 set metric-type
- 29.25 set origin
- 29.26 set originator-id
- 29.27 set tag
- 29.28 set vpnv4 next-hop
- 29.29 set weight
- 29.30 show ip prefix-list
- 29.31 show ip prefix-list
- 29.32 show route-map
- 29.33 show router-id
Chapter 30 Commands for Static Route
- 30.1 ip route
- 30.2 show ip route
- 30.3 show ip route vrf
- 30.4 ip route vrf
Chapter 31 Commands for RIP
- 31.1 accept-lifetime
- 31.2 address-family ipv4
- 31.3 clear ip rip route
- 31.4 debug rip
- 31.5 debug rip redistribute message send
- 31.6 debug rip redistribute route receive
- 31.7 default-information originate
- 31.8 default-metric
- 31.9 distance
- 31.10 distribute-list
- 31.11 exit-address-family
- 31.12 ip rip aggregate-address
- 31.13 ip rip authentication key-chain
- 31.14 ip rip authentication mode
- 31.15 ip rip authentication string
- 31.16 ip rip authentication cisco-compatible
- 31.17 ip rip receive-packet
- 31.18 ip rip receive version
- 31.19 ip rip send-packet
- 31.20 ip rip send version
- 31.21 ip rip split-horizon
- 31.22 key
- 31.23 key chain
- 31.24 key-string
- 31.25 maximum-prefix
- 31.26 neighbor
- 31.27 network
- 31.28 offset-list
- 31.29 passive-interface
- 31.30 recv-buffer-size
- 31.31 redistribute
- 31.32 route
- 31.33 router rip
- 31.34 send-lifetime
- 31.35 show debugging rip
- 31.36 show ip protocols rip
- 31.37 show ip rip
- 31.38 show ip rip database
- 31.39 show ip rip interface
- 31.40 show ip rip aggregate
- 31.41 timers basic
- 31.42 version
Chapter 32 Commands for RIPng
- 32.1 clear ipv6 route
- 32.2 default-information originate
- 32.3 default-metric
- 32.4 distance
- 32.5 distribute-list
- 32.6 debug ipv6 rip
- 32.7 debug ipv6 rip redistribute message send
- 32.8 debug ipv6 rip redistribute route receive
- 32.9 ipv6 rip aggregate-address
- 32.10 ipv6 rip split-horizon
- 32.11 ipv6 router rip
- 32.12 neighbor
- 32.13 offset-list
- 32.14 passive-interface
- 32.15 redistribute
- 32.16 redistribute ospf
- 32.17 route
- 32.18 router ipv6 rip
- 32.19 show debugging ipv6 rip
- 32.20 show ipv6 rip interface
- 32.21 show ipv6 rip redistribute
- 32.22 show ipv6 protocols rip
- 32.23 show ipv6 rip
- 32.24 show ipv6 rip database
- 32.25 show ipv6 rip aggregate
- 32.26 show ipv6 rip redistribute
- 32.27 timers basic
Chapter 33 Commands for OSPF
- 33.1 area authentication
- 33.2 area default-cost
- 33.3 area filter-list
- 33.4 area nssa
- 33.5 area range
- 33.6 area stub
- 33.7 area virtual-link
- 33.8 auto-cost reference-bandwidth
- 33.9 compatible rfc1583
- 33.10 clear ip ospf process
- 33.11 debug ospf events
- 33.12 debug ospf ifsm
- 33.13 debug ospf lsa
- 33.14 debug ospf nfsm
- 33.15 debug ospf nsm
- 33.16 debug ospf packet
- 33.17 debug ospf route
- 33.18 debug ospf redistribute message send
- 33.19 debug ospf redistribute route receive
- 33.20 default-information originate
- 33.21 default-metric
- 33.22 distance
- 33.23 distribute-list
- 33.24 host area
- 33.25 ip ospf authentication
- 33.26 ip ospf authentication-key
- 33.27 ip ospf cost
- 33.28 ip ospf database-filter
- 33.29 ip ospf dead-interval
- 33.30 ip ospf disable all
- 33.31 ip ospf hello-interval
- 33.32 ip ospf message-digest-key
- 33.33 ip ospf mtu
- 33.34 ip ospf mtu-ignore
- 33.36 ip ospf priority
- 33.37 ip ospf retransmit-interval
- 33.38 ip ospf transmit-delay
- 33.39 key
- 33.40 key chain
- 33.41 log-adjacency-changes detail
- 33.42 max-concurrent-dd
- 33.43 neighbor
- 33.44 network area
- 33.45 ospf abr-type
- 33.46 ospf router-id
- 33.47 overflow database
- 33.48 overflow database external
- 33.49 passive-interface
- 33.50 redistribute
- 33.51 redistribute ospf
- 33.52 router ospf
- 33.53 show ip ospf
- 33.54 show ip ospf border-routers
- 33.55 show ip ospf database
- 33.56 show ip ospf interface
- 33.57 show ip ospf neighbor
- 33.58 show ip ospf redistribute
- 33.59 show ip ospf route
- 33.60 show ip ospf virtual-links
- 33.61 show ip route process-detail
- 33.62 show ip protocols
- 33.63 summary-address
- 33.64 timers spf
Chapter 34 Commands for OSPFv3
- 34.1 area default cost
- 34.2 area range
- 34.3 area stub
- 34.4 area virtual-link
- 34.5 abr-type
- 34.6 default-metric
- 34.7 debug ipv6 ospf events
- 34.8 debug ipv6 ospf ifsm
- 34.9 debug ipv6 ospf lsa
- 34.10 debug ipv6 ospf nfsm
- 34.11 debug ipv6 ospf nsm
- 34.12 debug ipv6 ospf packet
- 34.13 debug ipv6 ospf redistribute message send
- 34.14 debug ipv6 ospf redistribute route receive
- 34.15 debug ipv6 ospf route
- 34.16 ipv6 ospf cost
- 34.17 ipv6 ospf dead-interval
- 34.18 ipv6 ospf display route single-line
- 34.19 ipv6 ospf hello-interval
- 34.21 ipv6 ospf retransmit-interval
- 34.22 ipv6 ospf transmit-delay
- 34.23 ipv6 router ospf
- 34.24 max-concurrent-dd
- 34.25 passive-interface
- 34.26 redistribute
- 34.27 redistribute ospf
- 34.28 router-id
- 34.29 router ipv6 ospf
- 34.30 show ipv6 ospf
- 34.31 show ipv6 ospf database
- 34.32 show ipv6 ospf interface
- 34.33 show ipv6 ospf neighbor
- 34.34 show ipv6 ospf route
- 34.35 show ipv6 ospf redistribute
- 34.36 show ipv6 ospf topology
- 34.37 show ipv6 ospf virtual-links
- 34.38 show ipv6 route process-detail
- 34.39 timers spf
Chapter 35 Commands for BGP and MBGP4+
- 35.1 address-family
- 35.2 address-family ipv4
- 35.3 address-family vpnv4
- 35.4 aggregate-address
- 35.5 bgp aggregate-nexthop-check
- 35.6 bgp always-compare-med
- 35.7 bgp bestpath as-path ignore
- 35.8 bgp bestpath compare-confed-aspath
- 35.9 bgp bestpath compare-routerid
- 35.10 bgp bestpath med
- 35.11 bgp client-to-client reflection
- 35.12 bgp cluster-id
- 35.13 bgp confederation identifier
- 35.14 bgp confederation peers
- 35.15 bgp dampening
- 35.16 bgp default
- 35.17 bgp deterministic-med
- 35.18 bgp enforce-first-as
- 35.20 bgp inbound-route-filter
- 35.21 bgp inbound-max-route-num
- 35.22 bgp log-neighbor-changes
- 35.23 bgp network import-check
- 35.25 bgp rfc1771-strict
- 35.26 bgp router-id
- 35.27 bgp scan-time
- 35.28 clear ip bgp
- 35.29 clear ip bgp dampening
- 35.30 clear ip bgp flap-statistics
- 35.31 debug bgp
- 35.32 debug bgp redistribute message send
- 35.33 debug bgp redistribute route receive
- 35.34 debug ipv6 bgp redistribute message send
- 35.35 debug ipv6 bgp redistribute route receive
- 35.36 distance
- 35.37 distance bgp
- 35.38 exit-address-family
- 35.39 import map
- 35.40 ip as-path access-list
- 35.41 ip community-list
- 35.42 ip extcommunity-list
- 35.43 neighbor activate
- 35.44 neighbor advertisement-interval
- 35.45 neighbor allowas-in
- 35.46 neighbor attribute-unchanged
- 35.47 neighbor capability
- 35.48 neighbor capability orf prefix-list
- 35.49 neighbor collide-established
- 35.50 neighbor default-originate
- 35.51 neighbor description
- 35.52 neighbor distribute-list
- 35.53 neighbor dont-capability-negotiate
- 35.54 neighbor ebgp-multihop
- 35.55 neighbor enforce-multihop
- 35.56 neighbor filter-list
- 35.57 neighbor interface
- 35.58 neighbor maximum-prefix
- 35.59 neighbor next-hop-self
- 35.60 neighbor override-capability
- 35.61 neighbor passive
- 35.62 neighbor peer-group (Creating)
- 35.63 neighbor peer-group (Configuring group members)
- 35.64 neighbor port
- 35.65 neighbor prefix-list
- 35.66 neighbor remote-as
- 35.67 neighbor remove-private-AS
- 35.69 neighbor route-reflector-client
- 35.70 neighbor route-server-client
- 35.71 neighbor send-community
- 35.72 neighbor shutdown
- 35.73 neighbor soft-reconfiguration inbound
- 35.74 neighbor soo
- 35.75 neighbor strict-capability-match
- 35.76 neighbor timers
- 35.77 neighbor timers connect
- 35.78 neighbor unsuppress-map
- 35.79 neighbor update-source
- 35.80 neighbor version 4
- 35.81 neighbor weight
- 35.82 network (BGP)
- 35.83 redistribute (BGP)
- 35.84 redistribute ospf
- 35.85 redistribute ospf (MBGP4+)
- 35.86 rd
- 35.87 router bgp
- 35.88 route-target
- 35.89 set vpnv4 next-hop
- 35.90 show ip bgp
- 35.91 show ip bgp attribute-info
- 35.92 show ip bgp community
- 35.93 show ip bgp community-info
- 35.94 show ip bgp community-list
- 35.95 show ip bgp dampening
- 35.96 show ip bgp filter-list
- 35.97 show ip bgp inconsistent-as
- 35.98 show ip bgp neighbors
- 35.99 show ip bgp paths
- 35.101 show ip bgp quote-regexp
- 35.102 show ip bgp regexp
- 35.103 show ip bgp route-map
- 35.104 show ip bgp scan
- 35.105 show ip bgp summary
- 35.106 show ip bgp view
- 35.107 show ip bgp view neighbors
- 35.108 show ip bgp vpnv4
- 35.109 show ipv6 bgp redistribute
- 35.110 timers bgp
Chapter 36 Commands for Black Hole Routing
- 36.1 ip route null0
- 36.2 ipv6 route null0
Chapter 37 Commands for ECMP
- 37.1 maximum-paths
Chapter 38 IPv4 Multicast Protocol
- 38.1 Public Commands for Multicast
  - 38.1.1 show ip mroute
- 38.2 Commands for PIM-DM
- 38.3 Commands for PIM-SM
- 38.4 Commands for MSDP Configuration
- 38.5 Commands for ANYCAST RP v4
- 38.6 Commands for PIM-SSM
  - 38.6.1 ip multicast ssm
- 38.7 Commands for DVMRP
- 38.8 Commands for DCSCM
- 38.9 Commands for IGMP
- 38.10 Commands for IGMP Snooping
- 38.11 Commands for IGMP Proxy
Chapter 39 IPv6 Multicast Protocol
- 39.1 Public Commands for Multicast
  - 39.1.1 show ipv6 mroute
- 39.2 Commands for PIM-DM6
- 39.3 Commands for PIM-SM6
- 39.4 Commands for ANYCAST RP v6
- 39.5 Commands for PIM-SSM6
  - 39.5.1 ipv6 pim ssm
- 39.6 Commands for IPv6 DCSCM
- 39.7 Commands for MLD
- 39.8 Commands for MLD Snooping Configuration
Chapter 40 Commands for Multicast VLAN
- 40.1 multicast-vlan
- 40.2 multicast-vlan association
Chapter 41 Commands for ACL
- 41.1 absolute-periodic/periodic
- 41.2 absolute start
- 41.3 access-list (ip extended)
- 41.4 access-list (ip standard)
- 41.5 access-list(mac extended)
- 41.6 access-list(mac-ip extended)
- 41.7 access-list(mac standard)
- 41.8 clear access-group statistic interface
- 41.9 firewall
- 41.10 firewall default
- 41.11 ip access extended
- 41.12 ip access standard
- 41.13 ipv6 access-list
- 41.14 ipv6 access standard
- 41.15 ipv6 access extended
- 41.16 {ip|ipv6|mac|mac-ip} access-group
- 41.17 mac access extended
- 41.18 mac-ip access extended
- 41.19 permit | deny (ip extended)
- 41.20 permit | deny(ip standard)
- 41.21 permit | deny(ipv6 extended)
- 41.22 permit | deny(ipv6 standard)
- 41.23 permit | deny(mac extended)
- 41.24 permit | deny(mac-ip extended)
- 41.25 show access-lists
- 41.26 show access-group
- 41.27 show firewall
- 41.28 show ipv6 access-lists
- 41.29 show time-range
- 41.30 time-range
Chapter 42 Commands for 802.1x
- 42.1 debug dot1x detail
- 42.2 debug dot1x error
- 42.3 debug dot1x fsm
- 42.4 debug dot1x packet
- 42.6 dot1x eapor enable
- 42.7 dot1x enable
- 42.8 dot1x ipv6 passthrough
- 42.9 dot1x guest-vlan
- 42.10 dot1x macfilter enable
- 42.11 dot1x max-req
- 42.12 dot1x user free-resource
- 42.13 dot1x max-user macbased
- 42.14 dot1x max-user userbased
- 42.16 dot1x port-method
- 42.17 dot1x privateclient enable
- 42.18 dot1x re-authenticate
- 42.19 dot1x re-authentication
- 42.20 dot1x timeout quiet-period
- 42.21 dot1x timeout re-authperiod
- 42.22 dot1x timeout tx-period
- 42.23 dot1x unicast enable
- 42.24 dot1x web authentication enable
- 42.25 dot1x web redirect
- 42.26 dot1x web redirect enable
- 42.27 show dot1x
Chapter 43 Commands for the Number Limitation Function of Port, MAC in VLAN and IP
- 43.1 switchport mac-address dynamic maximum
- 43.2 vlan mac-address dynamic maximum
- 43.3 switchport arp dynamic maximum
- 43.4 switchport nd dynamic maximum
- 43.5 ip arp dynamic maximum
- 43.6 ipv6 nd dynamic maximum
- 43.7 mac-address query timeout
- 43.8 show mac-address dynamic count
- 43.9 show arp-dynamic count
- 43.10 show nd-dynamic count
- 43.11 debug switchport mac count
- 43.12 debug switchport arp count
- 43.13 debug switchport nd count
- 43.14 debug vlan mac count
- 43.15 debug ip arp count
- 43.16 debug ipv6 nd count
Chapter 44 Commands for AM Configuration
- 44.1 am enable
- 44.2 am port
- 44.3 am ip-pool
- 44.4 am mac-ip-pool
- 44.5 no am all
- 44.6 show am
Chapter 45 Commands for Security Feature
- 45.1 dosattack-check srcip-equal-dstip enable
- 45.2 dosattack-check ipv4-first-fragment enable
- 45.3 dosattack-check tcp-flags enable
- 45.4 dosattack-check srcport-equal-dstport enable
- 45.5 dosattack-check tcp-fragment enable
- 45.6 dosattack-check tcp-segment
- 45.7 dosattack-check icmp-attacking enable
- 45.8 dosattack-check icmpv4-size
- 45.9 dosattack-check icmpv6-size
Chapter 46 Commands for TACACS+
- 46.1 tacacs-server authentication host
- 46.2 tacacs-server key
- 46.3 tacacs-server nas-ipv4
- 46.4 tacacs-server timeout
- 46.5 debug tacacs-server
Chapter 47 Commands for RADIUS
- 47.1 aaa enable
- 47.2 aaa-accounting enable
- 47.3 aaa-accounting update
- 47.4 debug aaa packet
- 47.5 debug aaa detail attribute
- 47.6 debug aaa detail connection
- 47.7 debug aaa detail event
- 47.8 debug aaa error
- 47.9 radius nas-ipv4
- 47.10 radius nas-ipv6
- 47.11 radius-server accounting host
- 47.12 radius-server authentication host
- 47.13 radius-server dead-time
- 47.14 radius-server key
- 47.15 radius-server retransmit
- 47.16 radius-server timeout
- 47.17 radius-server accounting-interim-update timeout
- 47.18 show aaa authenticated-user
- 47.19 show aaa authenticating-user
- 47.20 show aaa config
- 47.21 show radius count
Chapter 48 Commands for SSL Configuration
- 48.1 ip http secure-server
- 48.2 ip http secure-port
- 48.3 ip http secure- ciphersuite
- 48.4 show ip http secure-server status
- 48.5 debug ssl
Chapter 49 Commands for IPv6 Security RA
- 49.1 ipv6 security-ra enable
- 49.2 ipv6 security-ra enable
- 49.3 show ipv6 security-ra
- 49.4 debug ipv6 security-ra
Chapter 50 Commands for VLAN-ACL
- 50.1 clear vacl statistic vlan
- 50.2 show vacl vlan
- 50.3 vacl ip access-group
- 50.4 vacl ipv6 access-group
- 50.5 vacl mac access-group
- 50.6 vacl mac-ip access-group
Chapter 51 Commands for Mirroring Configuration
- 51.1 monitor session source interface
- 51.2 monitor session source interface access-list
- 51.3 monitor session destination interface
- 51.4 show monitor
Chapter 52 Commands for RSPAN Configuration
- 52.1 remote-span
- 52.2 monitor session remote vlan
- 52.3 monitor session reflector-port
Chapter 53 Commands for sFlow
- 53.1 sflow destination
- 53.2 sflow agent-address
- 53.3 sflow priority
- 53.4 sflow header-len
- 53.5 sflow data-len
- 53.6 sflow counter-interval
- 53.7 sflow rate
- 53.8 show sflow
Chapter 54 Commands for VRRP
- 54.1 advertisement-interval
- 54.2 circuit-failover
- 54.3 debug vrrp
- 54.4 disable
- 54.5 enable
- 54.6 interface
- 54.7 preempt-mode
- 54.8 priority
- 54.9 router vrrp
- 54.10 show vrrp
- 54.11 virtual-ip
Chapter 55 Commands for IPv6 VRRPv3 Configuration
- 55.1 advertisement-interval
- 55.2 circuit-failover
- 55.3 debug ipv6 vrrp
- 55.4 disable
- 55.5 enable
- 55.6 preempt-mode
- 55.7 priority
- 55.8 router ipv6 vrrp
- 55.10 virtual-ipv6 interface
Chapter 56 Commands for MRPP
- 56.1 control-vlan
- 56.2 clear mrpp statistics
- 56.3 debug mrpp
- 56.4 enable
- 56.5 fail-timer
- 56.6 hello-timer
- 56.7 mrpp enable
- 56.8 mrpp port-scan-mode
- 56.9 mrpp ring
- 56.10 mrpp ring primary-port
- 56.11 mrpp ring secondary-port
- 56.12 node-mode
- 56.13 show mrpp
- 56.14 show mrpp statistics
Chapter 57 Commands for ULPP
- 57.1 clear ulpp flush counter interface
- 57.2 control vlan
- 57.3 debug ulpp error
- 57.4 debug ulpp event
- 57.5 debug ulpp flush content interface
- 57.6 debug ulpp flush {send | receive} interface
- 57.7 description
- 57.8 flush disable arp
- 57.9 flush disable mac
- 57.10 flush enable arp
- 57.11 flush enable mac
- 57.12 preemption delay
- 57.13 preemption mode
- 57.14 protect vlan-reference-instance
- 57.15 show ulpp flush counter interface
- 57.16 show ulpp flush-receive-port
- 57.17 show ulpp group
- 57.18 ulpp control vlan
- 57.19 ulpp flush disable arp
- 57.20 ulpp flush disable mac
- 57.21 ulpp flush enable arp
- 57.22 ulpp flush enable mac
- 57.23 ulpp group
- 57.24 ulpp group master
- 57.25 ulpp group slave
Chapter 58 Commands for ULSM
- 58.1 debug ulsm event
- 58.2 show ulsm group
- 58.3 ulsm group
- 58.4 ulsm group {uplink | downlink}
Chapter 59 Commands for SNTP
- 59.1 debug sntp
- 59.2 sntp server
- 59.3 sntp polltime
- 59.4 sntp timezone
- 59.5 show sntp
Chapter 60 Commands for NTP
- 60.1 ntp enable
- 60.2 ntp server
- 60.3 ntp broadcast server count
- 60.4 ntp timezone
- 60.5 ntp access-group
- 60.6 ntp authenticate
- 60.7 ntp authentication-key
- 60.8 ntp trusted-key
- 60.9 ntp disable
- 60.10 ntp broadcast client
- 60.11 ntp multicast client
- 60.12 ntp ipv6 multicast client
- 60.13 debug ntp authentication
- 60.14 debug ntp packet
- 60.15 debug ntp adjust
- 60.16 debug ntp sync
- 60.17 debug ntp events
- 60.18 show ntp status
- 60.19 show ntp session
Chapter 61 Commands for DNSv4/v6
- 61.1 clear dynamic-host
- 61.2 debug dns
- 61.3 dns-server
- 61.4 dns lookup
- 61.5 show dns name-server
- 61.6 show dns domain-list
- 61.7 show dns hosts
- 61.8 show dns config
- 61.9 show dns client
- 61.10 ip domain-lookup
- 61.11 ip domain-list
- 61.12 ip dns server
- 61.13 ip dns server queue maximum
- 61.14 ip dns server queue timeout
Chapter 62 Commands for Show
- 62.1 clear logging
- 62.2 logging
- 62.3 ping
- 62.4 ping6
- 62.5 show debugging
- 62.6 show flash
- 62.7 show history
- 62.8 show logging buffered
- 62.9 show memory
- 62.10 show running-config
- 62.11 show startup-config
- 62.12 show switchport interface
- 62.13 show tcp
- 62.14 show telnet login
- 62.15 show temperature
- 62.16 show tech-support
- 62.17 show udp
- 62.18 show version
- 62.19 traceroute
- 62.20 traceroute6
Chapter 63 Commands for Reload Switch after Specified Time
- 63.1 reload after
- 63.2 reload cancel
- 63.3 show reload
Chapter 64 Commands for Debugging and Diagnosis for Packets Received and Sent by CPU
- 64.1 cpu-rx-ratelimit total
- 64.2 cpu-rx-ratelimit queue-length
- 64.3 cpu-rx-ratelimit protocol
- 64.4 clear cpu-rx-stat protocol
- 64.5 cpu-rx-ratelimit channel
- 64.6 show cpu-rx protocol
- 64.7 debug driver

See also other documents in the category PLANET Routers: