PLANET FSD-503 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the contents of your package for the following parts:
Fast Ethernet
Switch x 1
5V DC
1A Power
Adapter x 1
User’s
Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
3. Switch Front Panel
Figures 3-1 and 3-2 show the front panel of FSD-503 and
FSD-803, respectively.
Figure 3-1: FSD-503 Front Panel
Figure 3-2: FSD-803 Front Panel
6. Installing the Switch
This part describes how to install your Fast Ethernet Switch
and make connections to it. Please read the following topics
and perform the procedures in the order being presented.
Note
This Switch does not need software
configuration.
Desktop Installation
To install the Switch on desktop, simply follow the following
steps:
Step 1: Place the Switch on the desk near a power source.
Step 2: Keep some ventilation space between the Switch
and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions discussed
in Chapter 7 under Product Specifications.
5. Switch Rear Panel
Figures 5-1 and 5-2 show the rear panel of FSD-503 and
FSD-803, respectively.
1 2 3 4 5
5V DC
ON
OFF
Figure 5-1: FSD-503 Rear Panel
Figure 5-2: FSD-803 Rear Panel
2. Product Features
RJ-45 Interface
 5/8 10/100Mbps Fast Ethernet ports
 Complies with IEEE 802.3, 10Base-T, IEEE 802.3u
100Base-TX Ethernet standards
 Supports Auto MDI/MDI-X function
Switching
 Hardware based 10/100Mbps, half / full duplex, flow
control and auto-negotiation
 Features Store-and-Forward mode with wire-speed
filtering and forwarding rates
 IEEE 802.3x flow control for full duplex operation and
backpressure for half duplex operation
 Integrated address look-up engine, supporting 2K / 1K
absolute MAC addresses (FSD-503 / FSD-803)
 Handles up to 1536bytes packet
 Automatic address learning and address aging
 Supports CSMA/CD protocol
Hardware
 Made from metal, desktop size and wall-mount design
 LED indicators for system power, per port Link / Act
 5V DC, 1A external power adapter
 One power on/off button for energy saving
 FCC, CE Class B compliant
4. LED Indicators
FSD-503/FSD-803
LED Color Function
PWR Green
Light
Indicates that the Switch is powered
ON.
OFF
Indicates that the Switch is powered
OFF.
Link/
ACT
Green
Light
Indicates the link through that
port is successfully established at
10/100Mbps.
Blink
Indicates the Switch is actively
sending or receiving data over that
port.
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is powered.
If your networks should be active all
the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge
suppression device may also help to protect
your Switch from being damaged by
unregulated surge or current to the Switch
or the power adapter.
Step 3: Connect your Switch to network devices.
A. Connect one end of a standard network cable
to the 10/100 RJ-45 ports on the Rear Panel of
the Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 4: Supply power to the Switch.
A. Connect one end of the power cable to the
Switch.
B. Connect the 5V DC power adapter to a
standard wall outlet.
When the Switch receives power, the Power LED should
remain solid Green.
PC/Laptop
xDSL/Cable Router Internet Power Adapter
RJ-45
RJ-45
Power
001101010