HEIDENHAIN TNC 407 (243 020) Technical Manual User Manual
Page 751
01.98
TNC 407/TNC 415
Subject Index
13-11
S
S ............................................................... 8-18
S (SET) .................................................... 7-48
S-analogue voltage for gear range ............ 4-97
Scale datum............................................ 4-126
Scaling factor .......................................... 4-147
Scaling factor axis-specific ....................... 2-18
Scanning cycles ...................................... 4-182
S-code..................................................... 4-104
S-code - minimum spindle speed ........... 4-104
S-code acknowledgement, ..................... 4-104
S-code change signal.............................. 4-104
S-code table............................................ 4-105
SE 510 ...................................................... 3-38
SEARCH FEATURE NOT ALLOWED ....... 8-50
Secondary linear axis ................................ 4-13
Serial........................................................... 8-4
Servo lag.......................................... 4-68; 4-75
Servo lag, control with.............................. 4-66
Servo positioning ...................................... 4-65
Servo resolution........................................ 4-71
SET (S) .................................................... 7-48
SET NOT (SN) ......................................... 7-50
Shift Commands....................................... 7-93
SHIFT LEFT (<<)..................................... 7-93
SHIFT RIGHT (>>) .................................. 7-94
Shifting the datum .................................. 4-221
Shifting the reference points .................... 4-63
Signal designations................................... 8-12
Signal period ............................................... 4-6
SN (SET NOT) ......................................... 7-50
Sockets..................................................... 2-11
Soft key .................................................. 4-164
Soft keys................................................... 3-68
Software ..................................................... 2-7
Software handshaking ................................ 8-9
Software limit switch................................ 4-53
Software limit switches............................ 4-16
Software limit-switch.............................. 4-264
Software option .......................................... 2-8
Software protection module. 2-8; 4-180; 4-189
Software replacement .............................. 2-13
Software types ........................................... 2-7
S-override ................................................. 4-99
Special functions .................................... 4-275
Special tool ............................................... 2-15
Speed controller, optimizing ................... 11-12
Spindel in position .................................. 4-109
Spindle...................................................... 4-94
Spindle orientation........................... 3-27; 4-94
Spindle rotation left ................................ 4-101
Spindle rotation right .............................. 4-101
Spindle run-in characteristic ................... 4-118
Spindle run-on time ................................ 4-114
Spindle speed for gear ranges .................. 4-97
Spindle speed range ............................... 4-104
Spindle-orientation .................................. 4-106
Spindle-speed output................................ 4-94
Stack Operations .................................... 7-100
Stack, Load (PSL).................................... 7-101
Stack, Load (PSW) .................................. 7-102
Stack, Load Data (PS) ............................. 7-100
Stack, Pull (PLL) ...................................... 7-102
Stack, Pull (PLW) .................................... 7-102
Stack, Pull Data (PL) ............................... 7-101
Standard data transmission protocol ........ 8-10
Standard transmission protocol ................ 8-28
Standstill monitoring ................................. 4-87
Start bit ....................................................... 8-6
Status Interrogation (RPLY) .................... 7-124
Status, read............................................. 7-141
Status, write ........................................... 7-144
Status-window........................................ 4-134
Step switch............................................... 3-49
Stiction...................................................... 4-33
Stiction compensation ..................... 2-18; 4-33
Stop bits...................................................... 8-6
Storing a STRING (=) ............................ 7-116
STRING accumulator .............................. 7-114
STRING Execution .................................. 7-114
STRING memory..................................... 7-114
String Processing.................................... 7-151
Strobe ....................................................... 7-23
Strobe signal for M-function...................... 4-159
Stylus ...................................................... 4-195
Stylus deflected ...................................... 4-178
Stylus deflection ..................................... 4-191
Stylus deflection ..................................... 4-181
SUBM (SUBMIT)................................... 7-123
Submit Programs .................................... 7-123
Submit Queue......................................... 7-123
Subprograms .......................................... 7-123
SUBTRACT [ ] (–[ ]).................................. 7-85
SUBTRACTION (–) .................................. 7-67
Surface cutting speed............................. 4-195
Swivel axes............................................... 4-41
Synchronized axes .................................... 4-49