HEIDENHAIN TNC 407 (243 020) Technical Manual - Manual (Page 451)

6-2
TNC 407/TNC 415/TNC 425 61 List of markers 01.98
Marker Function Set Reset Page
M2045 Strobe signal for M-function NC NC 4-159
M2046 Strobe signal T code (P code) with TOOL CALL NC NC 4-229
M2047 Strobe signal 2nd T code (2nd P code) with TOOL DEF NC NC 4-229
M2048 Tapping cycle called NC NC 4-114
M2051 Operating mode: Manual NC NC 7-177
M2052 Operating mode: Electronic handwheel NC NC 7-177
M2053 Operating mode: Positioning with manual data input NC NC 7-177
M2054 Operating mode: Program run, single block NC NC 7-177
M2055 Operating mode: Program run, full sequence NC NC 7-177
M2057 Operating mode: Traversing the reference marks NC NC 7-177
M2059 Block scan (mid-program startup) is active NC;
PLC NC;
PLC 4-148
M2061 END-PGM, or M02 or M30 has been executed NC NC 4-154
M2064 S-Code 1st bit (lsb) 7-177
M2065 S-Code 2nd bit 7-177
M2066 S-Code 3rd bit 7-177
M2067 S-Code 4th bit 7-177
M2068 S-Code 5th bit 7-177
M2069 S-Code 6th bit 7-177
M2070 S-Code 7th bit 7-177
M2071 S-Code 8th bit (msb) 7-177
M2072 M-Code 1st bit (lsb) 7-177
M2073 M-Code 2nd bit 7-177
M2074 M-Code 3rd bit 7-177
M2075 M-Code 4th bit 7-177
M2076 M-Code 5th bit 7-177
M2077 M-Code 6th bit 7-177
M2078 M-Code 7th bit 7-177
M2079 M-Code 8th bit (msb) 7-177
M2080 Minimum rpm from MP3020 1st bit (lsb) 7-177
M2081 Minimum rpm from MP3020 2nd bit 7-177
M2082 Minimum rpm from MP3020 3rd bit 7-177
M2083 Minimum rpm from MP3020 4th bit 7-177
M2084 Minimum rpm from MP3020 5th bit 7-177
M2085 Minimum rpm from MP3020 6th bit 7-177
M2086 Minimum rpm from MP3020 7th bit 7-177
M2087 Minimum rpm from MP3020 8th bit (msb) 7-177
M2088 Increment from MP3020 1st bit (lsb) 7-177
M2089 Increment from MP3020 2nd bit 7-177
M2090 Increment from MP3020 3rd bit 7-177
M2091 Increment from MP3020 4th bit (msb) 7-177
M2092 Illegal spindle speed NC NC 4-102
M2093 Another T code (P code) follows with TOOL CALL NC NC 4-231
M2094 Maximum tool life elapsed (Time 1 in the tool table) PLC NC;PLC 4-227
M2095 Tapping – rigid tapping active NC NC 4-118
M2096 X Key last pressed NC NC 4-135
M2097 Y Key last pressed NC NC 4-135
M2098 Z key last pressed NC NC 4-135
M2099 Key IV last pressed NC NC 4-135
M2100 X-axis is tool axis NC NC 4-14