HEIDENHAIN TNC 407 (243 020) Technical Manual User Manual
Page 742
13-2 TNC 407/TNC 415 Subject Index 01.98
A
A ............................................................... 8-18
A (AND)................................................... 7-53
A[ ] (AND [ ])............................................ 7-80
Acceleration.......................... 4-68; 4-74; 4-260
Acceleration pre-control.......................... 11-10
Accessories ................................................ 2-5
Acknowledgement, of M-function.......... 4-159
Activation of a gear range....................... 4-101
Active axes ................................................. 4-6
Actual - nominal value transfer ................. 4-92
Actual spindle speed ................................ 4-95
ADD (+)................................................. 7-115
ADD [ ] (+[ ])............................................ 7-85
ADDITION (+) ......................................... 7-66
Address allocation .................................... 7-18
Address range .......................................... 7-18
Alphabetic keyboard ............................... 4-164
Amplitude of the measuring
system signals.......................................... 4-10
AN (AND NOT)........................................ 7-55
AN[ ] (AND NOT [ ])................................. 7-80
Analogue inputs.................... 3-53; 3-60; 4-206
Analogue inputs........................................ 3-18
Analogue output ............................ 4-95; 4-275
Analogue outputs ................................... 4-207
Analogue voltage ...................................... 4-70
AND (A)................................................... 7-53
AND [ ] (A[ ])............................................ 7-80
AND NOT (AN)........................................ 7-55
AND NOT [ ] (AN[ ].................................. 7-80
Angle encoders......................................... 3-27
Angular measurement ................................ 4-7
Angular measuring systems ..................... 3-24
APE......................................................... 4-176
APE........................................................... 3-36
APE 510.................................................... 3-38
Arc end-point tolerance ................. 2-15; 4-155
Arithmetic Commands.............................. 7-66
ASCII code.................................................12-2
Assembly hints ........................................... 3-9
ASSIGN (=) ............................................. 7-43
ASSIGN BYTE (B=) ................................. 7-45
Assign command...................................... 7-36
ASSIGN DOUBLEWORD (D=) ............... 7-45
ASSIGN NOT (=N) .................................... 7-46
ASSIGN TWO'S COMPLEMENT (= -) ...... 7-46
ASSIGN WORD (W=) ............................. 7-45
Assignment .............................................. 4-13
Assignment of the analogue outputs ....... 4-14
Assignment of the measuring
system inputs ........................................... 4-13
Assignment table.....................................7-161
Asynchronous data format ......................... 8-5
Auxiliary axes ............................................ 4-38
Axes in motion.......................................... 4-91
Axes in position ........................................ 4-90
Axis clamped ............................................ 4-92
Axis designation............................... 4-12; 4-13
Axis displayed on VDU ............................. 4-14
Axis error compensation........................... 2-16
Axis-enable ............................................... 4-89
Axis-error compensation........................... 4-23
Axis-limit ................................................... 4-16
Axis-stop on TOOL CALL ....................... 4-102
B
B= (ASSIGN BYTE) ................................. 7-45
Backlash compensation ............................ 4-23
BACKUP........................................... 2-13; 2-18
Bar Chart................................................. 7-155
Basic language - English ......................... 4-153
Battery voltage low................................. 4-178
BAUD RATE NOT POSSIBLE ................... 8-48
Baud rates................................................... 8-8
BC (BIT CLEAR) ...................................... 7-97
BC 110 B................................... 3-4; 3-70; 3-77
BCC.................................................. 8-18; 8-36
BIT RESET (BC)...................................... 7-97
Bit Commands .......................................... 7-96
BIT SET (BS) ........................................... 7-96
BIT TEST (BT).......................................... 7-98
Block Check Character .................... 8-10; 8-36
Block numbers - step size ...................... 4-151
Block processing time ................................ 2-3
Block scan...................................... 2-16; 4-149
Block transfer............................................ 8-19
Bolt hole circle ............................................ 9-9
BS (BIT SET) ........................................... 7-96
BT (BIT TEST).......................................... 7-98
Buffer battery............................................ 3-18
Byte ................................................. 7-16; 7-18