beautypg.com

HEIDENHAIN TNC 407 (243 020) Technical Manual User Manual

Page 749

background image


01.98 TNC 407/TNC 415 Subject Index 13-9

P

P ............................................................... 8-18
PA 110 ............................. 3-5; 3-18; 3-80; 4-32
Pallet file ................................................. 7-157
Pallet table ................................................ 8-18
Pallet-table .............................................. 4-150
Parallel ........................................................ 8-4
Parallel operation ........................................ 2-4
Parentheses with arithmetic commands.. 7-85
Parentheses with comparison commands7-89
Parentheses with logical gating................ 7-80
Parity bit...................................................... 8-6
Parity-check ................................................ 8-7
PASS OVER REFERENCE ........................ 4-53
Path dependent lubrication....................... 4-19
Picture distortion ...................................... 3-13
Picture disturbance................................... 3-13
PL (PULL).............................................. 7-101
PL 400 ............................. 3-4; 3-17; 3-57; 3-78
PL 410 ............................................. 3-59; 3-79

PLC axes...................... 2-18; 2-20; 4-38; 7-171
PLC data interface, configuration ............. 8-47
PLC dialogues......................................... 4-152
PLC EDIT ...................................... 5-5; 7-6; 7-7
PLC error message................................. 4-142
PLC error messages ................................. 2-15
PLC inputs ................................................ 3-54
PLC inputs - technical data ....................... 3-52
PLC inputs/outputs ................................... 3-51
PLC output................................................ 3-55
PLC outputs - technical data..................... 3-52
PLC positioning....................... 2-15; 4-35; 4-53
PLC program............................................. 8-18
PLC RUN .................................................... 5-5
PLC software............................................ 2-11
PLC window ..................... 4-141; 7-114; 7-152
PLC, Data transfer by ............................... 8-47
PLC-cycle time............................................ 7-6
PLC-DIALOG........................................... 7-115
PLC-Dialogue .......................................... 7-119
PLC-EPROM ............................................. 2-14
PLC-ERROR............................................ 7-115
PLC-functions ............................................. 7-6
PLC-inputs ................................................ 7-27
PLC-operation ............................................. 7-6
PLC-positioning module............................ 10-2
PLC-run....................................................... 7-6
PLL (PULL LOGICACCU) ...................... 7-102
PLW (PULL WORDACCU).................... 7-102
Pocket milling ......................................... 4-145
Pocket table.............................................. 8-18
Pockets with free-programmed contours 4-146
Polarity of the nominal value potential ....... 4-8

Polarity of the S-analogue voltage ............ 4-95
Position approach speed.................. 4-74; 4-76
Position control loop ................................. 4-65
Position display ....................................... 4-134
Position display with rotary axes ............ 4-135
Position monitoring................................... 4-84
Position values.......................................... 2-16
Positional deviation ................................... 4-71
Positioning error............................... 4-84; 4-85
Positioning module .......................... 8-20; 10-2
Positioning window .................................. 4-87
Positioning window for spindle............... 4-108
Positioning window for tool axis............. 4-118
Positive backlash ...................................... 4-23
Power consumption.................................. 3-16
POWER INTERRUPTED ......................... 4-155
Power supply ............................................ 3-16
Powers of 2 .............................................. 12-5
PP.INT..................................................... 4-180
PP.INT..................................................... 4-183
Pre-cut out time ...................................... 4-116
Probe system............................................ 2-19
Probing direction..................................... 4-192
Probing feed rate ........................ 4-176; 4-177;

.......................................... 4-180; 4-191; 4-192

Processing time .......................................... 7-7
Program creation ...................................... 7-16
PROGRAM INCOMPLETE........................ 8-48
PROGRAM INCOMPLETE............... 8-49; 8-50
PROGRAM NOT PRESENT ...................... 8-50
Program structure..................................... 7-16
Program Structures................................. 7-127
Programmed spindle speed...................... 4-95
Programming station .............................. 4-153
PROTECTED FILE..................................... 8-50
Protection, IP degree of............................ 3-13
PS (PUSH)............................................. 7-100
PSL (PUSH LOGICACCU) ..................... 7-101
PSW (PUSH WORDACCU) ................... 7-102
Pt 100 .............................................. 3-53; 4-32
Pt 100 ....................................................... 3-18