Dell POWEREDGE M1000E - Manual (Page 266)

190 Fabric OS Message Reference
53-1001767-01
FABS-1005
27
FABS-1005
Message
, [FABS-1005], ,, WARNING, ,
name and description of problem> (= )
Probable Cause Indicates that an unsupported operation has been requested. This is usually an internal Fabric OS
problem or file corruption. The possible value for function name and description of problem is:
fabsys_write: Unsupported write operation: process xxx
where xxx is the process ID (PID), which could be any whole number.
Recommended
Action
Reboot or power cycle the active CP (for modular systems) or the switch (for single-board systems).
If the message persists, run the firmwareDownload command to update the firmware.
Severity WARNING
FABS-1006
Message
, [FABS-1006], ,, WARNING, ,
name and description of problem>: object unit Probable CauseIndicates that there is no device in the slot with the specified object type ID in the system module
record. This could indicate a serious Fabric OS data problem on the switch. The possible values for
function name and description of problem are:•setSoftState: bad object•setSoftState: invalid type or unit•media_sync: Media oid mapping failed•fabsys_media_i2c_op: Media oid mapping failed•fabsys_media_i2c_op: obj is not media type•media_class_hndlr: failed sending media state to blade driver RecommendedActionIf the message is isolated, monitor the error messages on the switch. If the error is repetitive or if
the fabric failed, fail over or reboot the switch.If the message persists, run the firmwareDownload command to update the firmware.SeverityWARNINGFABS-1007Message, [FABS-1007], ,, WARNING, , name>: Media state is invalid - status=Probable CauseIndicates that the Fabric OS has detected an invalid value in an object's status field. This is usually
an internal Fabric OS problem or file corruption.RecommendedActionReboot or power cycle the switch.If the message persists, run the firmwareDownload command to update the firmware. Pages: 1 … 264 265 266 267 268 … 842 wrong Brand wrong Model non readable See also other documents in the category Dell Computer Accessories: POWEREDGE 2950 (10 pages) POWEREDGE 2950 (15 pages) POWEREDGE 2950 (182 pages) POWEREDGE 2950 (112 pages) POWEREDGE 2950 (186 pages) Console Switch (58 pages) PowerConnect 2024 (46 pages) 2161DS-2 (56 pages) 5316M (15 pages) PowerConnect M6348 (737 pages) PRECISION 530 (8 pages) PRECISION 530 (126 pages) PRECISION 530 (300 pages) INFINISCALE III M2401G (27 pages) POWEREDGE RADI H700 (29 pages) ? PowerEdge 6800 (31 pages) POWEREDGE M1000E (1082 pages) POWEREDGE M1000E (2 pages) POWEREDGE M1000E (9 pages) POWEREDGE M1000E (26 pages) POWEREDGE M1000E (42 pages) POWEREDGE M1000E (130 pages) POWEREDGE M1000E (12 pages) POWEREDGE M1000E (28 pages) POWEREDGE M1000E (80 pages) POWEREDGE M1000E (126 pages) POWEREDGE M1000E (20 pages) POWEREDGE M1000E (222 pages) POWEREDGE M1000E (54 pages) POWEREDGE M1000E (302 pages) POWEREDGE M1000E (41 pages) POWEREDGE M1000E (310 pages) POWEREDGE M1000E (2 pages) POWEREDGE M1000E (586 pages) POWEREDGE M1000E (1168 pages) POWEREDGE M1000E (1080 pages) POWEREDGE M1000E (64 pages) POWEREDGE M1000E (14 pages) POWEREDGE M1000E (116 pages) POWEREDGE M1000E (34 pages) POWEREDGE M1000E (86 pages) POWEREDGE M1000E (72 pages) POWEREDGE M1000E (94 pages) POWEREDGE M1000E (138 pages) POWEREDGE M1000E (382 pages) Sitemap
Probable Cause Indicates that there is no device in the slot with the specified object type ID in the system module
record. This could indicate a serious Fabric OS data problem on the switch. The possible values for
function name and description of problem are:
• setSoftState: bad object
• setSoftState: invalid type or unit
• media_sync: Media oid mapping failed
• fabsys_media_i2c_op: Media oid mapping failed
• fabsys_media_i2c_op: obj is not media type
• media_class_hndlr: failed sending media state to blade driver
Recommended
Action
If the message is isolated, monitor the error messages on the switch. If the error is repetitive or if
the fabric failed, fail over or reboot the switch.
If the message persists, run the firmwareDownload command to update the firmware.
Severity WARNING
FABS-1007
Message
, [FABS-1007], ,, WARNING, ,
name>: Media state is invalid - status=
Probable Cause Indicates that the Fabric OS has detected an invalid value in an object's status field. This is usually
an internal Fabric OS problem or file corruption.
Recommended
Action
Reboot or power cycle the switch.
If the message persists, run the firmwareDownload command to update the firmware.