SECTION 7
• SETUP
TABLE OF CONTENTS
SECTION 7
• SETUP ................................................................................................................................ 7-1
Introduction ............................................................................................................................................ 7-1
DGC-2020 Initial Setup .......................................................................................................................... 7-1
Initial Setup Required to Operate Unit ............................................................................................... 7-1
General Settings ............................................................................................................................. 7-1
Communications ............................................................................................................................. 7-2
System Parameters ........................................................................................................................ 7-3
Relay Control .................................................................................................................................. 7-7
Auto Config Detection ..................................................................................................................... 7-7
Alarm Configuration ........................................................................................................................ 7-8
Programmable Senders ................................................................................................................ 7-10
Initial Setup (Optional) ...................................................................................................................... 7-13
General Settings ........................................................................................................................... 7-13
Setting Up DGC-2020 Programmable Inputs and Outputs .................................................................. 7-15
Enable LSM-2020, CEM-2020, and AEM-2020 ............................................................................... 7-16
Programmable Inputs ....................................................................................................................... 7-16
Configuration Instructions ............................................................................................................. 7-16
Programmable Outputs .................................................................................................................... 7-26
Configuring Contact Outputs on the DGC-2020 ........................................................................... 7-26
Setting Up Configurable Elements in the DGC-2020. .................................................................. 7-28
Configuring Remote Contact Outputs on the CEM-2020 (See Figure 7-34) ................................ 7-29
Configuring Remote Analog Outputs on the AEM-2020 ............................................................... 7-30
Generator and Bus Breaker Control .................................................................................................... 7-31
Steps Required to Configure a DGC-2020 for Generator Breaker Control ...................................... 7-32
Synchronizer ........................................................................................................................................ 7-35
Steps Required to Configure a DGC-2020 Automatic Synchronizer ............................................... 7-36
Setting up a DGC-2020 and LSM-2020 for a Load Sharing and kW Control Application ................... 7-46
Load Sharing Overview and Theory of Operation in the DGC-2020................................................ 7-46
kvar Control Overview and Theory of Operation in the DGC-2020 .................................................. 7-48
Setup of the DGC-2020 and the LSM-2020 for Load Sharing and/or kW Control ........................... 7-48
Step by Step Setup Procedures ................................................................................................... 7-49
Mains Fail Transfer .............................................................................................................................. 7-60
Steps Required to Configure a DGC-2020 for Mains Fail Transfer ................................................. 7-60
Figures
Figure 7-1. Settings Explorer, General Settings, Style Number Screen ................................................... 7-1
Figure 7-2. Settings Explorer, Communications, CAN Bus Setup Screen ................................................ 7-2
Figure 7-3. Settings Explorer, Communications, ECU Setup Screen ....................................................... 7-3
Figure 7-4. Settings Explorer, System Parameters, System Settings Screen .......................................... 7-4
Figure 7-5. Settings Explorer, System Parameters, Rated Data ............................................................... 7-4
Figure 7-6. Settings Explorer, System Parameters, Remote Module Setup Screen ................................ 7-5
Figure 7-7. Settings Explorer, System Parameters, Crank Settings Screen ............................................. 7-6
Figure 7-8. Settings Explorer, System Parameters, Sensing Transformers Screen ................................. 7-7
Figure 7-9. Settings Explorer, System Parameters, Relay Control Screen............................................... 7-7
Figure 7-10. Settings Explorer, System Parameters, Auto Config Detection Screen ............................... 7-8
Figure 7-11. Settings Explorer, Alarm Configuration, Horn Configuration Screen .................................... 7-8
Figure 7-12. Settings Explorer, Alarm Configuration, Pre-Alarms Screen ................................................ 7-9
Figure 7-13. Settings Explorer, Alarm Configuration, Alarms Screen ....................................................... 7-9
Figure 7-14. Settings Explorer, Alarm Configuration, Sender Fail Screen .............................................. 7-10
Figure 7-15. Settings Explorer, Programmable Senders, Coolant Temperature Screen ........................ 7-11
Figure 7-16. Settings Explorer, Programmable Senders, Oil Pressure Screen ...................................... 7-12
Figure 7-17. Settings Explorer, Programmable Senders, Fuel Level Screen ......................................... 7-13
Figure 7-18. Settings Explorer, General Settings, Front Panel HMI Screen ........................................... 7-14
Figure 7-19. Settings Explorer, General Settings, Device Security Setup Screen .................................. 7-14
Figure 7-20. Settings Explorer, General Settings, Clock Setup Screen .................................................. 7-15
9400200990 Rev X
DGC-2020 Setup
i
