Basler Electric DGC-2020 User Manual
Page 101
Event String
Event Description
Event
Type
ALG IN X U1 (X = 1 to 8)
User Configurable Analog Input X Under 1 (X = 1 to 8)
Status
ALG IN X U1 A (X = 1 to 8)
User Configurable Analog Input X Under 1 (X = 1 to 8)
Alarm
ALG IN X U1 P (X = 1 to 8)
User Configurable Analog Input X Under 1 (X = 1 to 8)
Pre-Alarm
ALG IN X U2 (X = 1 to 8)
User Configurable Analog Input X Under 1 (X = 1 to 8)
Status
ALG IN X U2 A (X = 1 to 8)
User Configurable Analog Input X Under 1 (X = 1 to 8)
Alarm
ALG IN X U2 P (X = 1 to 8)
User Configurable Analog Input X Under 1 (X = 1 to 8)
Pre-Alarm
ATS INPUT CLOSED
ATS Input
Status
AUTO MODE
DGC-2020 has entered Auto mode.
Status
AUTO RESTART
Automatic Restart in Progress
Status
AUTO RESTART FAIL A
Automatic Restart Fail
Alarm
BATT CHRG FAIL A
Battery Charger Fail
Alarm
BATT CHRG FAIL P
Battery Charger Fail
Pre-Alarm
BATT OVERVOLT P
Battery Overvoltage
Pre-Alarm
BATTLE OVERRIDE
Battle Override
Status
BUS REV ROT
Bus Reverse Rotation
Pre-Alarm
CAN BUS OFF
CAN bus entered Bus Off state
Status
CAN ERROR PASSIVE
CAN bus entered Error Passive state
Status
CEM COMM FAIL P
CEM-2020 Communications Failure
Pre-Alarm
CEM HW MISMATCH P
Connected CEM-2020 is wrong type
Pre-Alarm
CHECKSUM FAIL P
Corrupt user settings or firmware code
Pre-Alarm
COMBINED RED A
Combined Red
Alarm
COMBINED YELLOW P
Combined Yellow
Pre-Alarm
CONF PROT X O1 (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Over Threshold 1
Status
CONF PROT X O1 A (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Over Threshold 1
Alarm
CONF PROT X O1 P (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Over Threshold 1
Pre-Alarm
CONF PROT X O2 (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Over Threshold 2
Status
CONF PROT X O2 A (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Over Threshold 2
Alarm
CONF PROT X O2 P (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Over Threshold 2
Pre-Alarm
CONF PROT X U1 (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Under Threshold 1
Status
CONF PROT X U1 A (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Under Threshold 1
Alarm
CONF PROT X U1 P (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Under Threshold 1
Pre-Alarm
CONF PROT X U2 (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Under Threshold 2
Status
CONF PROT X U2 A (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Under Threshold 2
Alarm
CONF PROT X U2 P (X = 1 to 8)
Configurable Protection X (X = 1 to 8) Under Threshold 2
Pre-Alarm
CONFIG ELEMENT X A (X = 1 to 8)
Configurable Element X (X = 1 to 8)
Alarm
CONFIG ELEMENT X P (X = 1 to 8)
Configurable Element X (X = 1 to 8)
Pre-Alarm
COOL LVL SNDR FL A
Coolant Level Sender Fail
Alarm
COOL SNDR FAIL
Coolant Temperature Sender Fail
Status
COOL SNDR FAIL A
Coolant Temperature Sender Fail
Alarm
COOL SNDR FAIL P
Coolant Temperature Sender Fail
Pre-Alarm
DEFAULTS LOADED
Default settings were uploaded into the DGC, indicating either a
successful firmware upload or a manual reset (UP and DOWN
pushbuttons being held).
Status
DEF ENGINE DERATE P
Diesel Exhaust Fluid Engine Derate
Pre-Alarm
DEF FLUID EMPTY P
Diesel Exhaust Fluid Empty
Pre-Alarm
DEF FLUID LOW P
Diesel Exhaust Fluid Low
Pre-Alarm
DEF INDUCMT O-RIDE P
Diesel Exhaust Fluid Inducement Override
Pre-Alarm
DEF PRESVR INDUCMT P
Diesel Exhaust Fluid Pre-Severe Inducement
Pre-Alarm
DEF SEVERE INDUCMT P
Diesel Exhaust Fluid Severe inducement
Pre-Alarm
DEF WARNING
Diesel Exhaust Fluid Pre-Inducement Warning Level 1
Pre-Alarm
DEF WARNING LEVEL 2
Diesel Exhaust Fluid Pre-Inducement Warning Level 2
Pre-Alarm
DEMAND START
Demand Start Request
Status
DEMAND STOP
Demand Stop Request
Status
DGC HEARTBEAT FAIL P
DGC-2020 Heartbeat Fail
Pre-Alarm
DIAG TRBL CODE P
Diagnostic Trouble Code
Pre-Alarm
DIAL OUT FAILED
Modem Dialout Failed
Status
DIAL OUT SUCCESS
Modem Dialout Success
Status
DPF REGNRATE DISABLD P
Regeneration Disabled
Pre-Alarm
9400200990 Rev X
DGC-2020 Functional Description
3-27