H3C Technologies H3C SecPath F1000-E User Manual

Page 906

881

Enable IPv6 multicast routing and IPv6 administrative scoping, and enable IPv6 PIM-SM and MLD:
# Enable IPv6 multicast routing and IPv6 administrative scoping on Router A, enable IPv6 PIM-SM
on each interface, and enable MLD on the host-side interface GigabitEthernet 0/1.

system-view

[RouterA] multicast ipv6 routing-enable

[RouterA] pim ipv6

[RouterA-pim6] c-bsr admin-scope

[RouterA-pim6] quit

[RouterA] interface GigabitEthernet 0/1

[RouterA-GigabitEthernet0/1] mld enable

[RouterA-GigabitEthernet0/1] pim ipv6 sm

[RouterA-GigabitEthernet0/1] quit

[RouterA] interface GigabitEthernet 0/2

[RouterA-GigabitEthernet0/2] pim ipv6 sm

[RouterA-GigabitEthernet0/2] quit

The configuration on Router C and Router F is similar to that on Router A.
# On SecPath A, enable IPv6 multicast routing and IPv6 administrative scoping, and enable IPv6
PIM-SM on each interface.

system-view

[SecPathA] multicast ipv6 routing-enable

[SecPathA] pim ipv6

[SecPathA-pim6] c-bsr admin-scope

[SecPathA-pim6] quit

[SecPathA] interface GigabitEthernet 0/1

[SecPathA-GigabitEthernet0/1] pim ipv6 sm

[SecPathA-GigabitEthernet0/1] quit

[SecPathA] interface GigabitEthernet 0/2

[SecPathA-GigabitEthernet0/2] pim ipv6 sm

[SecPathA-GigabitEthernet0/2] quit

[SecPathA] interface GigabitEthernet 0/3

[SecPathA-GigabitEthernet0/3] pim ipv6 sm

[SecPathA-GigabitEthernet0/3] quit

[SecPathA] interface GigabitEthernet 0/4

[SecPathA-GigabitEthernet0/4] pim ipv6 sm

[SecPathA-GigabitEthernet0/4] quit

The configuration on SecPath B, Router B, SecPath C, Router D, and Router E is similar to that on

SecPath A. (Details not shown.)

Configure an IPv6 admin-scoped zone boundary:
# On SecPath A, configure GigabitEthernet 0/3 and GigabitEthernet 0/4 as the boundary of IPv6
admin-scoped zone 1.

[SecPathA] interface GigabitEthernet 0/3

[SecPathA-GigabitEthernet0/3] multicast ipv6 boundary scope 4

[SecPathA-GigabitEthernet0/3] quit

[SecPathA] interface GigabitEthernet 0/4

[SecPathA-GigabitEthernet0/4] multicast ipv6 boundary scope 4

[SecPathA-GigabitEthernet0/4] quit

This manual is related to the following products:

H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS H3C SecBlade LB Cards H3C SecPath L1000-A Load Balancer