Motorola DSP56301 User Manual
Page 369
Index
-13
Asynchronous 8-1
Synchronous 8-1
programming model 8-9
data registers 8-22
Receive Data (RXD) 8-4
recover synchronization 8-2
reset 8-5
RXD
,
TXD
,
SCLK
SCI Clock Control Register (SCCR) 8-7
,
,
8-19
bit definitions 8-19
Clock Divider (CD) 8-20
Clock Out Divider (COD) 8-19
Clock Prescaler (SCP) 8-19
programming sheet B-36
Receive Clock Mode Source (RCM) 8-19
Transmit Clock Source (TCM) 8-19
SCI Control Register (SCR) 8-7
,
bit defintions 8-12
Idle Line Interrupt Enable (ILIE) 8-13
programming sheet B-35
Receive with Exception Interrupt Enable
(REIE) 8-12
Receiver Enable (RE) 8-14
Receiver Wakeup Enable (RWU) 8-15
SCI Clock Polarity (SCKP) 8-12
SCI Receive Interrupt Enable (RIE) 8-13
SCI Shift Direction (SSFTD) 8-15
SCI Transmit Interrupt Enable (TIE) 8-13
Send Break (SBK) 8-15
Timer Interrupt Enable (TMIE) 8-13
Timer Interrupt Rate (STIR) 8-12
Transmitter Enable (TE) 8-14
Wakeup Mode Select (WAKE) 8-15
Wired-OR Mode Select (WOMS) 8-14
Word Select (WDS) 8-16
SCI Receive Data Register (SRX) 8-9
SCI Status Register (SSR) 8-9
bit definitions 8-17
Framing Error Flag (FE) 8-17
Idle Line Flag (IDLE) 8-18
Overrun Error Flag (OR) 8-18
Parity Error (PE) 8-17
Receive Data Register Full (RDRF) 8-18
Received Bit 8 (R8) 8-17
Transmit Data Register Empty (TDRE) 8-18
Transmitter Empty (TRNE) 8-18
SCI Transmit Data Address Register (STXA) 8-9
SCI Transmit Data Register (STX) 8-9
select wakeup on idle line mode 8-15
Serial Clock (
SCLK
) 8-4
state after reset 8-5
Synchronous mode 8-2
transmission priority
preamble, break, and data 8-7
transmit and receive shift registers 8-2
Transmit Data (
TXD
) 8-4
Transmit Data Register (STX or STXA) 8-22
Transmit Data Register (STX) 8-23
Wired-OR mode 8-3
Serial Control 0 (
SC00
and
SC10
) signals 7-4
Serial Control 1 (
SC01
and
SC11
) signals 7-4
Serial Control 2 (
SC02
and
SC12
) signals 7-6
Serial Control Direction 0 (SCD0) bit 7-23
Serial Control Direction 1 (SCD1) bit 7-23
Serial Control Direction 2 (SCD2) bit 7-23
Serial Input Flag 0 (IF0) bit 7-4
Serial Input Flag 1 (IF1) bit 7-29
Serial Output Flag (OF0–OF1) bits 7-18
Serial Output Flag 0 (OF0) bit 7-4
,
Serial Output Flag 1 (OF1) bit 7-23
Serial Receive Data (SRD) signal 7-3
Serial Transmit Data (STD) signal 7-3
setting timer operating mode 9-4
Shift Direction (SHFD) bit 7-22
Signaled System Error (SSE) bit 6-65
Signalled Target Abort (STA) bit 6-65
signals
by function 2-1
functional grouping 2-2
Sixteen-bit Arithmetic Mode (SA) bit 4-8
Sixteen-bit Compatibility (SC) mode 3-6
Sixteen-bit Compatibility (SC) mode bit 3-7
Size register (SZ) 1-8
Slave Fetch Type (SFT) 6-52
Slave Receive Data Request (SRRQ) bit 6-36
Slave Receive Interrupt Enable (SRIE) bit 6-26
Slave Transmit Data Request (STRQ) bit 6-37
Slave Transmit Interrupt Enable (STIE) bit 6-26
SRAM support 1-5
Stack Counter register (SC) 1-8
Stack Extension Enable (SEN) bit 4-12
Stack Extension Overflow Flag (EOV) bit 4-13
Stack Extension Underflow Flag (EUN) bit 4-13
Stack Extension Wrap Flag (WRP) bit 4-12
Stack Extension XY Select (XYS) bit 4-13
Stack Pointer (SP) 1-8
start-up procedure location 4-2
Status Register (SR) 1-8
bit definitions 4-7
Condition Code Register (CCR) 4-7
Carry (C) 4-11
Extension (E) 4-11
Limit (L) 4-11
Negative (N) 4-11
Overflow (V) 4-11
Scaling (S) 4-10
Unnormalized (U) 4-11