Rockwell Automation 592- E300 Overload Relay User Manual User Manual
E300 electronic overload relay
This manual is related to the following products:
Table of contents
Document Outline
- Bulletin 193/592 E300 Overload Relay User Manual
- Important User Information
- Table of Contents
- Chapter 1
- Chapter 2
- Installation and Wiring
- Introduction
- Receiving
- Unpacking/Inspecting
- Storing
- General Precautions
- Base Relay Assembly
- Control Module to Sensing Module Assembly
- Communication Module to Control Module Assembly
- Expansion Bus Peripherals
- Expansion Bus Digital & Analog I/O Modules and Power Supply Installation
- Expansion Bus Operator Station Installation
- Expansion Bus Network Installation
- Starter Assembly
- Starter Dimensions
- DIN Rail / Panel Mount Dimensions
- Expansion Bus Peripherals Dimensions
- Terminals
- Grounding
- Short-Circuit Ratings
- Fuse Coordination
- Typical Motor Connections
- External Line Current Transformer Application
- Control Circuits
- Installation and Wiring
- Chapter 3
- System Operation and Configuration
- Introduction
- Device Modes
- Option Match
- Enable Option Match Protection Trip (Parameter 186)
- Enable Option Match Protection Warning (Parameter 192)
- Control Module Type (Parameter 221)
- Sensing Module Type (Parameter 222)
- Communication Module Type (Parameter 223)
- Operator Station Type (Parameter 224)
- Digital I/O Expansion Module 1 Type (Parameter 225)
- Digital I/O Expansion Module 2 Type (Parameter 226)
- Digital I/O Expansion Module 3 Type (Parameter 227)
- Digital I/O Expansion Module 4 Type (Parameter 228)
- Analog I/O Expansion Module 1 Type (Parameter 229)
- Analog I/O Expansion Module 2 Type (Parameter 230)
- Analog I/O Expansion Module 3 Type (Parameter 231)
- Analog I/O Expansion Module 4 Type (Parameter 232)
- Option Match Action (Parameter 233)
- Security Policy
- I/O Assignments
- Input Pt00 Assignment (Parameter 196)
- Input Pt01 Assignment (Parameter 197)
- Input Pt02 Assignment (Parameter 198)
- Input Pt03 Assignment (Parameter 199)
- Input Pt04 Assignment (Parameter 200)
- Input Pt05 Assignment (Parameter 201)
- Output Pt00 Assignment (Parameter 202)
- Output Pt01 Assignment (Parameter 203)
- Output Pt02 Assignment (Parameter 204)
- Activate FLA2 with Output Relay (Parameter 209)
- Expansion Bus Fault
- Emergency Start
- Introduction to Operating Modes
- System Operation and Configuration
- Chapter 4
- Chapter 5
- Chapter 6
- Chapter 7
- Metering and Diagnostics
- Introduction
- Device Monitor
- Percent Thermal Capacity Utilized
- Time to Trip
- Time To Reset
- Current Trip Status
- Voltage Trip Status
- Power Trip Status
- Control Trip Status
- Current Warning Status
- Voltage Warning Status
- Power Warning Status
- Control Warning Status
- Input Status 0
- Input Status 1
- Output Status
- Operator Station Status
- Device Status 0
- Device Status 1
- Firmware Revision Number
- Control Module ID
- Sensing Module ID
- Operator Station ID
- Expansion Digital Module ID
- Operating Time
- Starts Counter
- Starts Available
- Time to Start
- Year
- Month
- Day
- Hour
- Minute
- Second
- Invalid Configuration Parameter
- Invalid Configuration Cause
- Mismatch Status
- Current Monitor
- Voltage Monitor
- Power Monitor
- Energy Monitor
- kWh 109
- kWh 106
- kWh 103
- kWh 100
- kWh 10-3
- kVARh Consumed 109
- kVARh Consumed 106
- kVARh Consumed 103
- kVARh Consumed 100
- kVARh Consumed 10-3
- kVARh Generated 109
- kVARh Generated 106
- kVARh Generated 103
- kVARh Generated 100
- kVARh Generated 10-3
- kVARh Net 109
- kVARh Net 106
- kVARh Net 103
- kVARh Net 100
- kVARh Net 10-3
- kVAh 109
- kVAh 106
- kVAh 103
- kVAh 100
- kVAh 10-3
- kW Demand
- Max kW Demand
- kVAR Demand
- Max kVAR Demand
- kVA Demand
- Max kVA Demand
- Trip / Warning History
- Trip Snapshot
- Metering and Diagnostics
- Chapter 8
- EtherNet/IP Communications
- Chapter 9
- Chapter 10
- Appendix A
- Appendix B
- Appendix C
- EtherNet/IP Information
- Common Industrial Protocol (CIP) Objects
- Identity Object — CLASS CODE 0x0001
- Message Router — CLASS CODE 0x0002
- Assembly Object — CLASS CODE 0x0004
- Instance 2
- Instance 50
- Instance 120 - Configuration Assembly Revision 2
- Instance 120 - Configuration Assembly Revision 1
- Instance 144 – Default Consumed Assembly
- Instance 198 - Current Diagnostics Produced Assembly
- Instance 199 - All Diagnostics Produced Assembly
- Connection Object — CLASS CODE 0x0005
- Discrete Input Point Object — CLASS CODE 0x0008
- Discrete Output Point Object — CLASS CODE 0x0009
- Analog Input Point Object — CLASS CODE 0x000A
- Analog Output Point Object — CLASS CODE 0x000B
- Parameter Object — CLASS CODE 0x000F
- Parameter Group Object — CLASS CODE 0x0010
- Discrete Output Group Object — CLASS CODE 0x001E
- Control Supervisor Object — CLASS CODE 0x0029
- Overload Object — CLASS CODE 0x002c
- Base Energy Object — CLASS CODE 0x004E
- Electrical Energy Object — CLASS CODE 0x004F
- Wall Clock Time Object — CLASS CODE 0x008B
- DPI Fault Object — CLASS CODE 0x0097
- DPI Warning Object — CLASS CODE 0x0098
- MCC Object — CLASS CODE 0x00C2
- Comm Adapter Info Object — CLASS CODE 0x0C8
- E300 Status Object — CLASS CODE 0x0375
- Common Industrial Protocol (CIP) Objects
- EtherNet/IP Information