Echelon SmartServer 2.2 - Manual (Page 112)

SmartServer 2.2 User’s Guide 113
4. Update the bootrom following these steps:
a. Connect a serial cable between your computer and the i.LON 100 e3 plus Server console port.
b. Start a terminal emulator such as PuTTY. Set the serial interface settings to 9600 bps, 8 bits,
no parity, 1 stop bit, and no flow control. See Appendix B, Using the SmartServer Console
Application, for more information on the console interface.
c. Open the SmartServer 2.2 (Release 4.06) bootrom images folder. To do this, click Start,
point to Programs, point to Echelon SmartServer 2.2 Software, select i.LON Image
Folder, and then open the BootROM 4.03 folder. Alternatively, you can browse to the file
path of the SmartServer 2.2 bootrom image folder, which is
LonWorks\iLon100\images\BootROM 4.03 by default.
d. Upload via FTP the updated bootrom.upd file to the root directory of your i.LON 100 e3 plus
Server.
e. Reboot the i.LON 100 e3 plus Server by entering the reboot command in the console
application. When the console reads “Press the ‘!’ key to stop auto-boot”,
press ‘!’. The i.LON 100 e3 plus Server will reboot to the bootrom state, halting all
applications.
f. Enter the update bootrom command in the console application. If the bootrom file name
is different than the default (bootrom.upd), specify the actual file name as an additional
parameter.
Note: Do not interrupt the bootrom update process. Doing so will render the i.LON 100 e3
plus Server unable to boot. If this happens, you will need to ship your SmartServer back to
Echelon to be repaired.
g. After the bootrom update has been completed, reboot your i.LON 100 e3 plus Server by
entering the reboot command in the console application.
5. Format the SmartServer flash disk using the bootrom console following these steps:
a. Enter the reboot command in the SmartServer console application.
b. When the console reads “Press the ‘!’ key to stop auto-boot”, press ‘!’. The
SmartServer will enter the bootrom state, halting all applications.
c. Enter the format command in the bootrom application. Your i.LON 100 e3 plus Server is
automatically rebooted.
See Appendix B, Using the SmartServer Console Application, for more information on using the
bootrom and console applications.
6. If the devices on you network have user-defined network variable types (UNVTs) or user-defined
configuration property types (UCPTs), copy the devices’ custom resource file sets (.ENU, .fmt,
.fpt, .ls, and .typ files) from the lonworks/types folder in the e3 backup to a
lonworks/types/User/<YourCompany> folder on the i.LON 100 e3 plus Server flash disk.
7. Open the SmartServer images folder. To do this, click Start, point to Programs, point to
Echelon SmartServer 2.2 Software, and the select i.LON Image Folder. Alternatively, you can
browse to the file path of the SmartServer 1.0 image folder, which is
LonWorks\iLon100\images\iLon100 4.02 by default.
8. Copy all the folders and files in the LonWorks\iLon100\images\iLon100 4.02 folder on your
computer to the root directory of the i.LON 100 e3 plus Server flash disk.
9. Copy the ltConfig, Config, and Web/user/<Custom> folders from the e3 plus backup to the root
directory of the i.LON 100 e3 plus Server flash disk. The ltConfig folder contains the
L
ON W ORKS connections and other L ON W ORKS data in your network; the Config folder contains