11 l_jogctrlextension_1, L_jogctrlextension_1, L_jogctrlexten – Lenze 8400 motec User Manual
Page 474: 12 function library
![background image](/manuals/566305/474/background.png)
12
Function library
12.11
L_JogCtrlExtension_1
474
Lenze · 8400 motec · Reference manual · DMS 4.1 EN · 08/2013 · TD05
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
12.11
L_JogCtrlExtension_1
This function extension is available from version 05.00.00!
This FB is connected upstream to the
ramp function generator/setpoint generator to
implement a switch-off positioning at limit switch.
• Detailed information on this operating mode can be found in the description of the
.
Inputs
Identifier
Data type
Information/possible settings
bInputSel1
bInputSel2
BOOL
Activation of the bSlowDown1/bStop1, bSlowDown2/bStop2 and bSlowDown3/
bStop3 signal pairs according to the
Truth table for activating the pre-switch off
bRfgIn
BOOL
Ramping down the ramp function generator in the downstream FB
according to the
Truth table - switch-off positioning
bJog1In
bJog2In
BOOL
Selection inputs for setting fixed speeds in the setpoint generator
• If the pre-switch off is inactive (bInputSel1 and bInputSel2 are both set to FALSE),
the two control signals are output one-to-one at the bJog1Out and bJog2Out
outputs.
• To achieve the desired behaviour (starting at high speed, pre-switch off at low
speed), both inputs must be set to TRUE.
• Fixed setpoint 2 must be less than fixed setpoint 3!
Otherwise, the drive will start at a low speed and accelerate after the pre-switch
off.
bSlowDown1
bSlowDown2
bSlowDown3
BOOL
Activation of the fixed setpoint 2 in the downstream FB
• These inputs only fulfil a function if they have been activated via bInputSel1 and
bInputSel2 previously (see
Truth table for activating the pre-switch off
).
bStop1
bStop2
bStop3
BOOL
Ramping down of the ramp function generator in the downstream FB
• These inputs only fulfil a function if they have been activated via bInputSel1 and
bInputSel2 previously (see
Truth table for activating the pre-switch off
).
/B-RJ&WUO([WHQVLRQB
E,QSXW6HO
E,QSXW6HO
E5IJ,Q
E-RJ,Q
E5IJ2XW
E-RJ2XW
E-RJ2XW
E-RJ,Q
E6WRS
E6ORZ'RZQ
E6WRS
E6ORZ'RZQ
E6WRS
E6ORZ'RZQ
'08;
&75/
&
&
&
&
&
&
&
&
&
&
&
(GJHGHWHFW
&
&
&
&
&
&
E5IJ2XW
E-RJ2XW
E-RJ2XW
25
$1'
$1'
/B-RJ&WUO([WHQVLRQBE5IJ2XW
(QWU\LQVHOHFWOLVW
/B-RJ&WUO([WHQVLRQBE-RJ2XW
/B-RJ&WUO([WHQVLRQBE-RJ2XW
&RQILJXUDWLRQ
SDUDPHWHUV