Brocade TurboIron 24X Series Configuration Guide - Manual (Page 893)

Brocade TurboIron 24X Series Configuration Guide 859
53-1003053-01
IGMP V3
If the tracking and fast leave feature is enabled, you can display the list of clients that belong to a
particular group by entering commands such as the following.
Syntax: show ip igmp group [ ] [ detail | tracking ]
If you want a report for a specific multicast group, enter that group address for .
Omit the if you want a report for all multicast groups.
Enter detail if you want to display the source list of the multicast group.
Enter tracking if you want information on interfaces that have tracking enabled.
The following table defines the statistics for the show ip igmp group command output.
TABLE 132 Output of show ip igmp group
This field Displays
Group The address of the multicast group
Phy-port The physical port on which the multicast group was received.
Static A “yes” entry in this column indicates that the multicast group was configured as a
static group; “No” means it was not. Static multicast groups can be configured in IGMP
V2 using the ip igmp static command. In IGMP V3, static sources cannot be configured
in static groups.
Querier “Yes” means that the port is a querier port; “No” means it is not. A port becomes a
non-querier port when it receives a query from a source with a lower source IP address
than the port.
Life Shows the number of seconds the interface can remain in exclude mode. An exclude
mode changes to include mode if it does not receive an "IS_EX" or "TO_EX" message
during a certain period of time. The default is 140 seconds. There is no "life" displayed
in include mode.
TurboIron#show ip igmp group 239.0.0.1 detail
Display group 239.0.0.1 in all interfaces.
Interface v18 : 1 groups
group phy-port static querier life mode #_src
1 239.0.0.1 e20 no yes include 19
group: 239.0.0.1, include, permit 19 (source, life):
(10.3.3.1 40) (10.3.3.2 40) (10.3.3.3 40) (10.3.3.4 40) (10.3.3.5 40)
(10.3.3.6 40) (10.3.3.7 40) (10.3.3.8 40) (10.3.3.9 40) (10.3.3.10 40)
(10.3.3.11 40) (10.3.3.12 40) (10.3.3.13 40) (10.3.3.14 40) (10.3.3.15 40)
(10.3.3.16 40) (10.3.3.17 40) (10.3.3.18 40) (10.3.3.19 40)
Interface v110 : 1 groups
group phy-port static querier life mode #_src
2 239.0.0.1 e5 no yes include 10
group: 239.0.0.1, include, permit 10 (source, life):
(10.2.3.0 80) (10.2.3.1 80) (10.2.3.2 80) (10.2.3.3 80) (10.2.3.4 80)
(10.2.3.5 80) (10.2.3.6 80) (10.2.3.7 80) (10.2.3.8 80) (10.2.3.9 80)
TurboIron#show ip igmp group 224.1.10.1 tracking
Display group 224.1.10.1 in all interfaces with tracking enabled.
Interface v13 : 1 groups, tracking_enabled
group phy-port static querier life mode #_src
1 224.1.10.1 e15 no yes include 3
receive reports from 3 clients:
10.110.110.7 10.110.10.8 10.110.110.9