Brocade TurboIron 24X Series Configuration Guide - Manual (Page 439)

Brocade TurboIron 24X Series Configuration Guide 405
53-1003053-01
Configuring super aggregated VLANs
NOTE
In these examples, the configurations of the edge devices (A, B, E, and F) are identical. The
configurations of the core devices (C and D) also are identical. The aggregated VLAN configurations
of the edge and core devices on one side must be symmetrical (in fact, a mirror image) to the
configurations of the devices on the other side. For simplicity, the example in
Figure 49 on page 402
is symmetrical in terms of the port numbers. This allows the configurations for both sides of the link
to be the same. If your configuration does not use symmetrically arranged port numbers, the
configurations should not be identical but must use the correct port numbers.
Commands for device A
TurboIronA(config)#vlan 101 by port
TurboIronA(config-vlan-101)#tagged ethernet 6
TurboIronA(config-vlan-101)#untagged ethernet 1
TurboIronA(config-vlan-101)#exit
TurboIronA(config)#vlan 102 by port
TurboIronA(config-vlan-102)#tagged ethernet 6
TurboIronA(config-vlan-102)#untagged ethernet 2
TurboIronA(config-vlan-102)#exit
TurboIronA(config)#vlan 103 by port
TurboIronA(config-vlan-103)#tagged ethernet 6
TurboIronA(config-vlan-103)#untagged ethernet 3
TurboIronA(config-vlan-103)#exit
TurboIronA(config)#vlan 104 by port
TurboIronA(config-vlan-104)#tagged ethernet 6
TurboIronA(config-vlan-104)#untagged ethernet 4
TurboIronA(config-vlan-104)#exit
TurboIronA(config)#vlan 105 by port
TurboIronA(config-vlan-105)#tagged ethernet 6
TurboIronA(config-vlan-105)#untagged ethernet 5
TurboIronA(config-vlan-105)#exit
vA(config)#write memory
Commands for device B
The commands for configuring device B are identical to the commands for configuring device A.
Notice that you can use the same channel VLAN numbers on each device. The devices that
aggregate the VLANs into a path can distinguish between the identically named channel VLANs
based on the ID of the path VLAN.
TurboIronB(config)#vlan 101 by port
TurboIronB(config-vlan-101)#tagged ethernet 6
TurboIronB(config-vlan-101)#untagged ethernet 1
TurboIronB(config-vlan-101)#exit
TurboIronB(config)#vlan 102 by port
TurboIronB(config-vlan-102)#tagged ethernet 6
TurboIronB(config-vlan-102)#untagged ethernet 2
TurboIronB(config-vlan-102)#exit
TurboIronB(config)#vlan 103 by port
TurboIronB(config-vlan-103)#tagged ethernet 6
TurboIronB(config-vlan-103)#untagged ethernet 3
TurboIronB(config-vlan-103)#exit
TurboIronB(config)#vlan 104 by port
TurboIronB(config-vlan-104)#tagged ethernet 6
TurboIronB(config-vlan-104)#untagged ethernet 4
TurboIronB(config-vlan-104)#exit