Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) - Manual (Page 629)

Unified IP MIB Reference 603
53-1003106-01
MPLS LSP table
60
mplsLspFrrAdmGrpIncludeAny
brcdIp.1.2.15.1.2.3.1.27
Syntax: MplsTunnelAffinity Read-only The administrative group setting that the device includes
any of the interfaces that are members of the group when
calculating detour routes for this LSP.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
mplsLspFrrAdmGrpIncludeAll
brcdIp.1.2.15.1.2.3.1.28
Syntax: MplsTunnelAffinity Read-only The administrative group setting that an interface must be
a member of all of the groups to be considered in a detour
route for the LSP. Any interface that is not a member of all
the groups is eliminated from consideration.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
mplsLspFrrAdmGrpExcludeAny
brcdIp.1.2.15.1.2.3.1.29
Syntax: MplsTunnelAffinity Read-only The administrative group setting that the device excludes
any of the interfaces that are members of the group when
calculating detour routes for this LSP.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
mplsLspPathSelectMode
brcdIp.1.2.15.1.2.3.1.30
Syntax: Integer Read-only Indicates the path selection mode to use:
•
Auto-select is the default mode. In this mode, the
primary path is always selected to carry traffic when
the primary path has stayed operating in the working
state for at least the amount of time specified in
mplsLspPathSelectRevertTimer.
•
For manual-select, the traffic is switched to a
user-selected path specified in
mplsLspPathSelectPathname after the selected path
has stayed operating in the working state for at least
the amount of time specified in
mplsLspPathSelectRevertTimer.
•
For unconditional-select, the traffic is switched to
and stays on the selected path regardless of the
path's condition, even if it is in a failure state.
mplsLspPathSelectPathname
brcdIp.1.2.15.1.2.3.1.31
Syntax: DisplayString Read-only The user-selected secondary path for path-select mode
"manual" and "unconditional".
mplsLspPathSelectRevertTimer
brcdIp.1.2.15.1.2.3.1.32
Syntax: Unsigned32 Read-only The number of seconds to wait after the primary or
selected path comes up before traffic reverts to that path.
A value of zero indicates that it will switch immediately
after the current working path goes down.
mplsLspShortcutOspfAllowed
brcdIp.1.2.15.1.2.3.1.33
Syntax: TruthVal Read-only Indicates that this LSP allows a shortcut between nodes in
an autonomous system (AS). The OSPF route includes the
LSP in its SPF calculation.
mplsLspShortcutIsisAllowed
brcdIp.1.2.15.1.2.3.1.34
Syntax: TruthVal Read-only Indicates that this LSP allows a shortcut through the
network to a destination based on the path's cost (metric).
The traffic is forwarded through this LSP to destinations
within the IS-IS routing domain. The IS-IS route includes
the LSP in its SPF calculation.
mplsLspShortcutIsisLevel
brcdIp.1.2.15.1.2.3.1.35
Syntax: Integer Read-only Indicates the level of the IS-IS routing enabled on the
device.
The value of this variable is not applicable if
mplsLspShortcutIsisAllowed is “False”.
Name, OID, and syntax Access Description