Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) - Manual (Page 336)

310 Unified IP MIB Reference
53-1003106-01
Port VLAN configuration table
23
snVLanByPortCfgBaseType
brcdIp.1.1.3.2.7.1.9
Syntax: Integer Read-only Indicates what type of bridging this bridge can perform. If a bridge is
actually performing a certain type of bridging, this will be indicated by
entries in the port table for the given type:
•
unknown(1)
•
transparentOnly(2)
•
sourcerouteOnly(3)
•
srt(4)
snVLanByPortCfgStpProtoc
olSpecification
brcdIp.1.1.3.2.7.1.10
Syntax: Integer Read-only Shows what version of STP is being run:
•
unknown(1)
•
decLb100(2) – Indicates the DEC LANbridge 100 Spanning Tree
Protocol.
•
ieee8021d(3) – IEEE 802.1d implementations will return this
value. If future versions of the IEEE Spanning Tree Protocol are
released that are incompatible with the current version, a new
value will be defined.
snVLanByPortCfgStpMaxAg
e
brcdIp.1.1.3.2.7.1.11
Syntax: Integer Read-only Shows the value of dot1dStpMaxAge, which is the maximum age that
the STP information can exist before it is discarded. The STP
information is learned from the network. The value of this object is in
hundredths of a second, and is the actual value that this bridge is
currently using.
(Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgStpHelloTi
me
brcdIp.1.1.3.2.7.1.12
Syntax: Timeout Read-only Shows the value of dot1dStpHelloTime, which is the interval between
the transmission of configuration bridge PDUs by this node. This value
applies to any port when it is the root of the spanning tree or is trying
to become the root. This is the actual value that this bridge is currently
using.
This value is in hundredths of a second.
(Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgStpHoldTi
me
brcdIp.1.1.3.2.7.1.13
Syntax: Integer32 Read-only Shows the value of dot1dStpHoldTime, which is the interval when no
more than two configuration bridge PDUs can be transmitted by this
node. The interval is in units of hundredths of a second.
(Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgStpForwar
dDelay
brcdIp.1.1.3.2.7.1.14
Syntax: Timeout Read-only Shows the value of dot1dStpForwardDelay, which controls how fast a
port changes its spanning state when moving towards the forwarding
state. The value determines how long the port stays in each of the
listening and learning states, which precede the forwarding state. This
value is also used, when a topology change has been detected and is
under way, to age all dynamic entries in the forwarding database.
NOTE: This value is the one that this bridge is currently using in
contrast to dot1dStpBridgeForwardDelay, which is the value
that this bridge and all others would start using should this
bridge become the root.
This value is measured in hundredths of a second. (Refer to
RFC 1493 Bridge MIB.)
snVLanByPortCfgStpTimeSi
nceTopologyChange
brcdIp.1.1.3.2.7.1.15
Syntax: Time ticks Read-only Shows the time since the last topology change was detected by the
bridge entity. This time is in hundredths of a second.
Name, OID, and syntax Access Description