Sndvmrpgraftretransmitti me, Sndvmrpdefaultroute, Dvmrp virtual interface table – Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) User Manual
Page 577: Sndvmrpvinterfacetable, Sndvmrpvinterfacevifindex, Sndvmrpvinterfacetype, Sndvmrpvinterfaceoperstate, Sndvmrpvinterfacelocaladdress, Sndvmrpvinterfaceremoteaddress
Unified IP MIB Reference
551
53-1003106-01
DVMRP virtual interface table
53
DVMRP virtual interface table
The DVMRP virtual interface table contains the router’s DVMRP virtual interfaces.
NOTE
The following table is not supported on the Brocade MLXe, Brocade NetIron MLX, Brocade NetIron
XMR, Brocade NetIron CES, and Brocade NetIron CER series devices.
snDvmrpGraftRetransmitTi
me
brcdIp.1.2.5.1.11
Syntax: Integer
Read-write
Defines how long a router that is sending a graft message will wait for
the first graft acknowledgement from an upstream router before
retransmitting that message. Subsequent retransmissions are sent at
an interval twice that of the preceding interval.
For NetIron platforms:
•
Valid values: 5 – 3600 seconds
•
Default: 10 seconds
For FastIron platforms:
•
Valid values: 2 – 10 seconds
•
Default: 3 seconds
snDvmrpDefaultRoute
brcdIp.1.2.5.1.12
Syntax: IpAddress
Read-write
This is the IP address of a router that is connected to one of the directly
attached subnets. If a multicast route is not present on the local router,
this default route will be used for multicast forwarding. The
object must be set to “enabled” before this object
can be written.
Name, OID, and syntax
Access
Description
Name, OID, and syntax
Access
Description
snDvmrpVInterfaceTable
brcdIp.1.2.5.1.13
None
The DVMRP virtual interface table.
snDvmrpVInterfaceVifIndex
brcdIp.1.2.5.1.13.1.1
Syntax: Integer
Read-only
The ifIndex value of this DVMRP virtual interface.
snDvmrpVInterfaceType
brcdIp.1.2.5.1.13.1.2
Syntax: Integer
Read-write
Indicates the type of this DVMRP virtual interface:
•
tunnel(1) – Tunnel interface, for which the interface is a
querier.
•
queries(2) – Tunnel interface, for which the interface is
not a querier.
•
subnet(3) – Physical interface, for which the interface is
not a querier.
snDvmrpVInterfaceOperState
brcdIp.1.2.5.1.13.1.3
Syntax: Integer
Read-only
Shows the current state of this DVMRP virtual interface:
•
up(1)
•
down(2)
snDvmrpVInterfaceLocalAddress
brcdIp.1.2.5.1.13.1.4
Syntax: IpAddress
Read-write
Shows the IP address of the local end of this DVMRP virtual
interface.
snDvmrpVInterfaceRemoteAddress
brcdIp.1.2.5.1.13.1.5
Syntax: IpAddress
Read-write
Shows the IP address of the remote end of this DVMRP virtual
interface.
For a tunnel, enter the IP address of the neighboring router.
For a subnet, enter the subnet address.