Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) - Manual (Page 603)

Unified IP MIB Reference 577
53-1003106-01
HQoS statistics table
57
HQoS statistics table
The Brocade NetIron MLX, Brocade NetIron XMR, and Brocade MLXe devices are provided with
Simple Network Management Protocol (SNMP) support for the Hierarchical Quality of Service
(HQoS) Statistics Management Information Base (MIB).
The clear hqos statistics command clears the HQoS statistics for CLI and SNMP. The HQoS
statistics is supported for all the HQoS features except the HQoS support for VPLS. The cumulative
HQoS statistics for LAG is not supported but the HQoS statistics for member ports of a LAG can be
collected.
Name, OID, and syntax Access Description
brcdHqosStatsTable
brcdIp.1.1.14.1.1.1 None A list of brcHqosPStats entries. The table contains information of
various HQoS counters. The HQoS is supported on
NI-MLX-10Gx8-M/D Line Processor (LP) modules.
brcdHqosIfIndex
brcdIp.1.1.14.1.1.1.1.1
Syntax: InterfaceIndex None The interface index where the HQoS is configured. The LP module
must be physically present and operationally up.
brcdHqosEndpointType
brcdIp.1.1.14.1.1.1.1.2
Syntax: Integer None The object specifies the endpoint type for HQoS scheduler.
•
other(1)
•
singleTaggedVlan(2)
•
dougleTaggedVlan(3)
•
bVlanIsid(4))
brcdHqosEndpointTag
brcdIp.1.1.14.1.1.1.1.3
Syntax: Unsigned32 None The object specifies the HQoS endpoint tag.
•
If the index brcdHqosEndpointType is other(1), then the object
has zero value.
•
If the index brcdHqosEndpointType is singleTaggedVlan(2),
dougleTaggedVlan(3) or bVlanIsid(4), then the object has VLAN
ID as value. The valid VLAN ID values ranges from 1 through
4094.
brcdHqosEndpointInnerTag
brcdIp.1.1.14.1.1.1.1.4
Syntax: Unsigned32 None The object specifies the HQoS endpoint inner tag.
•
If the index brcdHqosEndpointType is other(1) or
singleTaggedVlan(2), then the object has zero value.
•
If the index brcdHqosEndpointType is dougleTaggedVlan(3),
then the object has VLAN ID as value. The valid VLAN ID values
ranges from 1 through 4094.
•
If the index brcdHqosEndpointType is bVlanIsid(4), then the
object has ISID as value. The valid ISID values ranges from
256 through 16777214.
brcdHqosStatsPriority
brcdIp.1.1.14.1.1.1.1.5
Syntax: PortPriorityTC Read-only The priority of the packets that is stored in the queue. This is an
1-based index.
The HQoS queue with brcdHqosEndpointType value as other(1) has
eight priorities. All the other HQoS queues has four priorities, two
consecutive priorities are stored in one queue. In this case, the
valid values for the object are 1, 3, 5, and 7. The queue with priority
1 has the packets with priority 1 and 2 and the same applies for
priorities 3, 5, and 7 as well.
brcdHqosStatsDescription
brcdIp.1.1.14.1.1.1.1.6
Syntax: DisplayString None The object gives the HQoS scheduler node in full-path format with
each node separated by dot(.).