Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) - Manual (Page 337)

Unified IP MIB Reference 311
53-1003106-01
Port VLAN configuration table
23
snVLanByPortCfgStpTopCha
nges
brcdIp.1.1.3.2.7.1.16
Syntax: Counter32 Read-only Shows the total number of topology changes detected by this bridge
since the management entity was last reset or initialized.
snVLanByPortCfgStpRootCo
st
brcdIp.1.1.3.2.7.1.17
Syntax: Integer32 Read-only Shows the value of dot1dStpRootCost, which is the cost of the path to
the root as seen from this bridge.
(Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgStpRootPo
rt
brcdIp.1.1.3.2.7.1.18
Syntax: Integer32 Read-only Shows the value of dot1dStpRootPort, which is the port number of the
port which offers the lowest cost path from this bridge to the root
bridge.
(Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgStpDesign
atedRoot
brcdIp.1.1.3.2.7.1.19
Syntax: BridgeId Read-only Shows the value of dot1dStpDesignatedRoot, which is the bridge
identifier of the root of the spanning tree as determined by the
Spanning Tree Protocol as executed by this node. This value is used as
the root identifier parameter in all configuration bridge PDUs
originated by this node.
(Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgBaseBridg
eAddress
brcdIp.1.1.3.2.7.1.20
Syntax: MAC address Read-only Shows the MAC address used by this bridge when it must be referred
to in a unique fashion. It is recommended that this be the numerically
smallest MAC address of all ports that belong to this bridge; however,
it is only required to be unique. When concatenated with
dot1dStpPriority, a unique bridge identifier is formed, which is used in
the Spanning Tree Protocol.
snVLanByPortCfgVLanNam
e
brcdIp.1.1.3.2.7.1.21
Syntax: DisplayString Read-write Shows the name of the VLAN community string.
Valid values: Up to 32 characters
snVLanByPortCfgRouterIntf
brcdIp.1.1.3.2.7.1.22
Syntax: Integer32 Read-write This object is optional. It identifies the virtual interface for the router to
the VLAN, and applies only to the router. If an SNMP-Get value is zero,
that means this object was not configured.
snVLanByPortCfgRowStatus
brcdIp.1.1.3.2.7.1.23
Syntax: Integer Read-write Deletes a VLAN entry.
snVLanByPortCfgStpVersion
brcdIp.1.1.3.2.7.1.24
Syntax: Integer
NOTE: This object is
supported only on
the FastIron SuperX
devices.
Read-write Shows the version of Spanning Tree Protocol the bridge is currently
running:
•
stpCompatible(0) – STP (IEEE 802.1D)
•
rstp(2) – RSTP (IEEE 802.1w)
snVLanByPortCfgInOctets
brcdIp.1.1.3.2.7.1.25
Syntax: Counter64 Read-only The number of bytes received on this VLAN. This can be used as the
per-VE counter, if there is one-to-one mapping for VLAN-VE.
snVLanByPortCfgTranspare
ntHwFlooding
brcdIp.1.1.3.2.7.1.26
Syntax: Integer Read-write Enables or disables transparent VLAN flooding on a VLAN:
•
disabled(0)
•
enabled(1)
Default: disabled(0)
Name, OID, and syntax Access Description