beautypg.com

Measuring the loudness of clips – Grass Valley EDIUS Pro v.6.5 User Manual

Page 433

background image

411

Volume/Pan Adjustment

EDIUS - Reference Manual

3

Both [Measurement Group 1] and [Measurement Group 2] can be set so that measurement is performed as
follows.

- The loudness values of 2ch and 5.1ch can be measured together. (For example, set L-ch1, R-ch1 and

[Downmix]- No to [Measurement Group 1], and L-ch3, R-ch4, C-ch5, LS-ch7, RS-ch8, and [Downmix]- No to
[Measurement Group 2].)

- 5.1ch output and the downmix processing result can be measured together. (For example, set L-ch1, R-ch2,

C-ch3, LS-ch5, RS-ch6, and [Downmix] - [No.] to [Measurement Group 1], and set L-ch1, R-ch2, C-ch3,
LS-ch5, RS-ch6, and [Downmix] - [Equation - 2] to [Measurement Group 2].)

- In mono measurement, the same output channel is assigned to both L/R.

Measuring Loudness between In and Out points on the Timeline

Measure the loudness between In and Out points on the timeline.

1 Set the In and Out Points to the timeline.
Setting the In and Out Points on the Timeline

0

P227

2 Click [View] on the menu bar, and click [Loudness Meter].
The [Loudness Meter] dialog box appears.
[Loudness Meter] Dialog Box

0

P409

3 Select [ITU-R BS.1770-2] or [EBU R128] from the list of loudness standards, and click [Settings].
The [Loudness Meter Settings] dialog box appears.
[Loudness Meter Settings] dialog box

0

P410

3

You can also select the registered preset.

[Loudness Meter]

0

P77

4 In [Measurement Group 1] ([Measurement Group 2] if necessary), set where L/R/C/LS/RS channels are to be

remapped, and click [Settings].

5 Check [In/Out] in the [Loudness Meter] dialog box.
Enter the timecode in [In] or [Out] to change the In/Out points.

6 Click [Start] in the [Loudness Meter] dialog box, and click [Play].
Playback starts from the position 3 seconds before the In point on the timeline, and the loudness measurement value is
displayed as a chart or numerical value.

3

During measurement, volume in the part where exceeding the target level can be adjusted with the audio mixer.

Adjusting Volume/Pan with the Audio Mixer

0

P402

Measuring the Loudness of Clips

The loudness of clips in the bin can be measured.

1 Right-click a clip in the bin, and click [Loudness Measurement].
The [Loudness Measurement] dialog box appears.

2 Select [ITU-R BS.1770-2] or [EBU R128] from the list of loudness standards, and click [Settings].
The [Loudness Meter Settings] dialog box appears.
[Loudness Meter Settings] dialog box

0

P410

3

You can also select the registered preset.

[Loudness Meter]

0

P77

3 In [Measurement Group 1] ([Measurement Group 2] if necessary), set where L/R/C/LS/RS channels are to be

remapped, and click [Settings].

4 Move the timeline cursor to the position to start playback.

5 Click [In/Out] or [Entire File] at [Trigger], and click [OK].
The loudness measurement starts.
When measurement completes, the [Loudness Meter] dialog box appears. The loudness measurement value is
displayed as a chart or numerical value.
[Loudness Meter] Dialog Box

0

P409