Brocade BigIron RX Series Configuration Guide - Manual (Page 1541)

BigIron RX Series Configuration Guide 1463
53-1002484-04
Redundant management module
E
copy slot1 | slot2 flash [/ < from-dir-path>/] < from-name>
monitor | primary | secondary
“Copying files between a flash card and flash
memory”
on page 44
copy slot1 | slot2 image < file-name> “Copying software image from a flash card to the
flash memory”
on page 44
copy flash slot1 | slot2 < source-name> monitor | primary
| secondary | startup-config [ < dest-name>]
“Copying files between a flash card and a TFTP
server”
on page 46
copy flash flash monitor standby “Copying software images between active and
standby management modules”
on page 45
copy flash flash primary [standby] “Copying software images between active and
standby management modules”
on page 45
copy flash flash secondary [standby] “Copying software images between active and
standby management modules”
on page 45
copy flash lp < source-file> < dest-file> < slot-number> | all “Copying files from a management module to an
interface module”
on page 45
copy flash tftp < ip-addr> < dest-file-name> primary |
secondary
“Copying BigIron RX Series Multi-Service IronWare
images from flash memory to a TFTP server”
on
page 45
copy slot1 | slot2 tftp < ip-addr>
[/ < from-dir-path>/] < source-file> [ < dest-file>]
“Copying files between a flash card and a TFTP
server”
on page 46
copy tftp slot1 | slot2 < ip-addr>
[/ < from-dir-path>/] < source-file> < path-name> | monitor
| primary | secondary
“Copying files between a flash card and a TFTP
server”
on page 46
copy slot1 | slot2 startup-config
[/
< from-dir-path>/] < file-name>
“Copying the startup-config file between a flash card
and flash memory”
on page 46
copy startup-config slot1 | slot2
[/
< to-dir-path>/] < to-name>
“Copying the startup-config file between a flash card
and flash memory”
on page 46
copy startup-config tftp < ip-addr>
[/ < to-dir-path>] < to-name>
“Copying the startup-config file between flash
memory and a TFTP server”
on page 47
copy tftp startup-config < ip-addr>
[/ < from-dir-path>] < from-name>
“Copying the startup-config file between flash
memory and a TFTP server”
on page 47
copy running-config slot1 | slot2
[/
< to-dir-path>/] < to-name>
“Copying the running-config to a flash card or a TFTP
server”
on page 47
copy slot1 | slot2 running-config
[/
< from-dir-path>/] < from-name>
“Loading a running-config from a flash card or a TFTP
server”
on page 47
copy tftp running-config < ip-addr>
[/ < from-dir-path>/] < from-name> [overwrite]
“Loading a running-config from a flash card or a TFTP
server”
on page 47
cp [ < source-dir-path>] < source-file-name>
[ < dest-dir-path>] < dest-file-name>
“Copying files using the cp command” on page 48
boot system slot1 | slot2 [/ < dir-path>/] < file-name> “Rebooting from the system” on page 49
boot system tftp < ip-address> < file-name> “Rebooting from the system” on page 49
boot system flash secondary “Rebooting from the system” on page 49
boot system slot1 < file-name> | slot2 < file-name> | flash
secondary | tftp < ip-address> < file-name> | bootp
“Configuring the boot source for future reboots” on
page 50
Commands See ...