GE Industrial Solutions DV-300 DC Drive Users Manual - Manual (Page 444)

GEI-100332Ga
——— PARAMETER LISTS ———
10
50
Parameter No. Format
Value Access via
min max
Factory
American
Factory
European
Keyp.
RS485/
BUS/
Opt2-M
Term.
Opt2-A/
PDC
Failure code
Failure supply
Undervoltage
Overvoltage
Overcurrent
Heatsink
Hardware
DSP error
Interrupt error
Speed fbk
External fault
Overtemp motor
Field loss
Bus loss
Hw opt 1 failure
Opt2
Unknown
Enable seq err
417 U16 0 65535 R
5100h
3120h
3310h
2300h
4210h
5000h
6110h
6120h
7301h
9000h
4310h
3330h
8110h
7510h
7400h
1001h
9009h
- -
Real FF PID 418 I16 -10000 +10000 0 0 ü R/W - R
Enc 2 speed (rpm) 420 I16 -8192 +8192 - - ü R R
PD output PID 421 I16 -10000 +10000 0 0 ü R - -
Enable OPT2
Enabled
Disabled
425 U16 0 1 Disable Disable ü R/Z
1
0
- -
Enc 1 speed (rpm) 427 I16 -8192 +8192 - - ü R R
Prop filter [ms] 444 U16 0 1000 0 0 ü R/W - -
Speed up gain [%] 445 Float 0.00 100.00 0.00 0.00 ü R/W - -
Speed up base [ms] 446 Float 0 16000 1000 1000 ü R/W - -
Speed up filter [ms] 447 U16 0 1000 0 0 ü R/W - -
R&L Search
(Cur reg selftune)
OFF
ON
452 U16 0 1 OFF OFF ü R/Z
0
1
- -
Arm resistance [ ] 453 Float S S 0.500 0.500 ü R/W - -
Arm inductance [mH] 454 Float S S 4.00 4.00 ü R/W - -
Speed fbk error [%] 455 U16 0 100 22 22 ü R/Z - -
“Flux weak speed [%]
(Crossover speed [%])”
456 U16 0 100 100 100 ü R/Z - R
Enable fbk contr
Enabled
Disabled
457 U16 0 1 Disabled
0
Disabled
0
ü R/Z
1
0
- -
Enable fbk bypas
Enabled
Disabled
458 U16 0 1 0 0 ü R/Z
1
0
- -
Speed P bypass [%] 459 Float 0.00 100.00 10.00 10.00 ü R/W - -
Speed I bypass [%] 460 Float 0.00 100.00 1.00 1.00 ü R/W - -
Size selection
Standard
American
464 U16 0 1 1 1 ü R/Z
0
1
- -
Drive size [A] 465 U16 0 S S S ü R - R
Mains voltage [V] 466 U16 0 999 - - ü R - -
“Flux current max [%]
(Max field curr [%])”
467 U16 P468 100 100 100 ü R/W - R/W
“Flux current min [%]
(Min field curr [%])”
468 U16 0 P467 5 5 ü R/W - ----