Yokogawa Data Acquisition with PID Control CX2000 - Manual (Page 333)

12-2
IM 04L31A01-01E
Code Message Explanation/Countermeasures/Ref. section
92 Press [ESC] key to change to operation mode. Press the ESC key.
93 String including space or all space cannot be specified. Spaces are not allowed in the Web browser user
name and password.
94 More than one address cannot be specified. Only a single sender is allowed.
100 IP address doesn’t belong to class A, B, or C. See the Communication Interface User’s Manual.
101 The result of the masked IP address is all 0s or 1s. See the Communication Interface User’s Manual.
102 SUBNET mask is incorrect. See the Communication Interface User’s Manual.
103 The net part of default gateway is not equal to that of IP address. See the Communication Interface User’s Manual.
104 FTP client failed because the memory mode is ‘manual’. See the Communication Interface User’s Manual.
120 The start segment number is greater than the end segment number. See section 5.6.
121 The On-time is greater than the Off-time. See section 5.5.
122 Exceeded the number of events which can be set. See section 5.5.
130 The lower span limit is greater than the upper span limit. See section 4.6.
131 The range of the span is wider than 30000. See section 4.6.
132 The lower scale limit is greater than the upper scale limit. See section 4.6.
133 The range of the scale is wider than 30000. See section 4.6.
134 The lower and upper span limits of the PV range are equal. See section 4.6.
135 The lower span limit of the PV range is greater than the upper See section 4.6.
span limit.
136 The range of the PV range is wider than 30000. See section 4.6.
137 The lower span limit of the PV switching exceeds the PV range. See section 4.6.
138 The upper span limit of the PV switching exceeds the PV range. See section 4.6.
139 The lower and upper span limits of the PV switching are equal. See section 4.6.
140 The lower span limit of the PV switching is greater than the upper See section 4.6.
span limit.
141 The lower and upper limits of the output are equal. See section 4.9.
142 The lower limit of the output is greater than the upper limit. See section 4.9.
143 The lower and upper limits of the target setpoint are equal. See section 4.12.
144 The lower limit of the target setpoint is greater than the upper limit. See section 4.12.
145 The setting of the reference point is incorrect.(n.RP > n+1.RP) See section 4.8.
146 Incorrect input I/O data. (Set point number <> 2) See section 4.11.
147 Incorrect input I/O data. (Output(n-1) > Output(n)) See section 4.11.
148 Incorrect input I/O data. Input+Output exceeds the range. See section 4.11.
149 Incorrect input I/O data. (Input+Output(n-1) > Input+Output(n)) See section 4.11.
• Execution Errors
Code Message Explanation/Countermeasures/Ref. section
150 This action is not possible because sampling is in progress. See section 9.1.
151 This action is not possible during sampling, calculating or controlling. See section 9.1.
152 This action is not possible because saving is in progress. Wait until the saving ends.
153 This action is not possible because formatting is in progress. Wait until the formatting ends.
155 The message is not written while sampling is stopped. See sections 8.9 and 9.1.
160 Cannot load the specified data. Change the memory setting. See section 9.3.
165 Auto setting is not possible becase the target is not support. Use manual setting instead of auto setting.
See the Communication Interface User’s Manual.
166 This action is not possible because communication protocol is not Set the communication setting to “Master.”
“Modbus-M”. (See the Communication Interface User’s Manual.)
12.1 Messages