Dell POWEREDGE M1000E - Manual (Page 475)

Fabric OS Command Reference 443
53-1001764-02
ipSecConfig
2
Example 1
Secure traffic between two systems using AH protection with MD5 and configure IKE with
preshared keys. The two systems are a switch, BROCADE300 (IPv4 address 10.33.74.13), and an
external UNIX server (10.33.69.132
).
1. On the system console, log into the switch as Admin and enable IPSec.
switch:admin>
ipsecconfig --enable
2. Create an IPSec SA policy named AH01, which uses AH protection with MD5.
switch:admin>
ipsecconfig --add policy ips sa -t AH01 -p ah -auth hmac_md5
3. Create an IPSec proposal IPSEC-AH to use AH01 as SA.
switch:admin>
ipsecconfig --add policy ips sa-proposal -t IPSEC-AH -sa AH01
4. Configure the SA proposal’s lifetime in time units.
switch:admin>
ipsecconfig --add policy ips sa-proposal -t IPSEC-AH -lttime 280000 -sa AH01
5. Import the preshared key file (e.g., ipseckey.psk) using the seCcertUtil import command.
6. Configure an IKE policy for the remote peer.
switch:admin> ipsecconfig -- add policy ike -t IKE01 -remote 10.33.69.132 -id 10.33.74.13 \
-remoteid 10.33.69.132 -enc 3des_cbc -hash hmac_md5 -prf hmac_md5 -auth psk \
-dh modp1024 -psk ipseckey.psk
7. Create an IPSec transform named TRANSFORM01 to use transport mode to protect traffic
identified for IPSec protection and use IKE01 as the key management policy.
switch:admin>
ipsecconfig --add policy ips transform -t TRANSFORM01 -mode transport \
-sa-proposal IPSEC-AH -action protect -ike IKE01
8. Create traffic selectors to select the outbound and inbound traffic that needs to be protected.
switch:admin>
ipsecconfig --add policy ips selector -t SELECTOR-OUT \
-d out -l 10.33.74.13 -r 10.33.69.132 -transform TRANSFORM01
switch:admin>
ipsecconfig --add policy ips selector -t SELECTOR-IN \
-d in -l 10.33.69.132 -r 10.33.74.13 -transform TRANSFORM01
9. Verify the IPSec SAs created using IKE for above traffic flow using ipsecConfig --show
manual-sa -a. Refer to the “IPSec display commands” section for an example.
10. Perform the equivalent steps on the remote peer to complete the IPSec configuration. Refer to
your server administration guide for instructions.
Example 2
Secure traffic between two systems using ESP protection with 3DES_CBC encryption and SHA1
authentication, and configure IKE with RSA Certificates signed by the certification authority (CA).
The two systems are A SWITCH, BROCADE300 (IPv6 address fe80::220:1aff:fe34:2e82), and an
external UNIX host (IPv6 address fe80::205:1fff:fe51:f09e).
1. On the system console, log into the switch as Admin and enable IPSec.
switch:admin>
ipsecconfig --enable
2. Create an IPSec SA policy named ESP01, which uses ESP protection with 3DES and SHA1.
switch:admin>
ipsecconfig --add policy ips sa -t ESP01 -p esp -enc 3des_cbc -auth hmac_sha1
3. Create an IPSec proposal IPSEC-ESP to use ESP01 as the SA.
switch:admin> ipsecconfig --add policy ips sa-proposal -t IPSEC-ESP -sa ESP01