Meridian America Link/Customer Controlled Routing User Manual

Meridian link/customer controlled routing, Installation and upgrade guide

Meridian America Link/Customer Controlled Routing User Manual | 595 pages

Meridian America Link/Customer Controlled Routing User Manual | 595 pages

Table of contents

Document Outline

Title page
Publication history
Contents
About this guide
- References
Chapter 1: Meridian Link/CCR co-residency
- Co-residency overview
- Keycode
- Ethernet LAN-based PC
Chapter 2: Overview of Meridian Link
- Meridian Link application
- New with Meridian Link Release 5C
- Link overview
- Diagnostic tools
- Meridian 1
- Host
- Meridian Mail software requirements
- Operations, Administration, and Maintenance (OA&M)
Chapter 3: Overview of Customer Controlled Routing
- CCR application
- New with CCR Release 3C
- Application Module Link
- Diagnostic tools
- Consoles/printers
- Meridian 1
Chapter 4: Meridian Link/CCR hardware
- IPE Module
- IPE Module Options 21-81
- Application Module
Chapter 5: Hardware installation overview
- Preparing for installation
- Installing an IPE Module or an Application Module
Chapter 6: Site survey/installation checklist
- General information
- Delivery information
- Meridian 1 software checklists
- Meridian Mail hardware checklist to support Meridian Link
- IPE Module and Application Module: Meridian Link/CCR software
- Hardware
- Equipment room information
- Power and ground considerations
- Equipment cabling
- Equipment room cooling conditions
- Additional considerations
- Comments and recommendations
Chapter 7: Unpack and inspect hardware
- Receiving the IPE Module and Application Module components
- Unpacking the IPE Module and Application Module components
Chapter 8: Hardware installation procedures
- Installing the IPE Module
- Installing the Application Module
- Installing the power supply and disk/tape unit (Application Module)
- Checking the card option settings (Application Module)
- Installing an NTAK02 SDI/DCH card
- Installing an ESDI or MSDL card
Chapter 9: Meridian Link/CCR interface cabling
- IPE Module cabling
- Cabling the Option 11 IPE Module to external equipment
- Backplane cable rerouting for Options 21-81 CE/PE and IPE backplanes
- Cabling the Options 21-81 IPE Module to external equipment
- Application Module cabling
- Cabling the Application Module to external equipment
- Installing Ethernet LAN support
Chapter 10: Installing peripheral devices
- VT220, VT320, and VT420 terminals
- Personal computer running Reflection 4+
- Meridian Terminal Emulator (MTE 8)
- Dot-matrix printer switch settings
- LaserJet series II printer switch settings
- LaserJet series III printer switch settings
- LaserJet series IV printer switch settings
- DeskJet and DeskJet 500 printer switch settings
Chapter 11: Peripheral device cabling interface
- DCE and DTE connections
- Using an A/B switchbox to share system consoles
- Modems
Chapter 12: Meridian 1 configuration for Meridian Link/CCR
- Conventional notation
- Configuration overview
- Configuring the VSID, HSID, and AML prompts
- Configure ESDI port (X11 Release 17)
- Enable ESDI port (X81 phase 7 or X11 Release 17)
- Configure ESDI or MSDL port (X11 Release 18 or later)
- Enable ESDI or MSDL port (X11 Release 18 or later)
- Configure SDI port for conshare (X11 Release 17)
- Configure SDI port for conshare (X11 Release 18 or later)
- Enable SDI port
- Configuring DNIS to use auto-terminating trunks
- Configuring DNIS to use Incoming Digit Conversion
- Configure devices for status change host notification
- Configure ACD DNs
- Configure Control DNs (CCR)
- Configuring a Phantom Loop
- Configuring a Phantom Superloop
- Creating a Phantom Set
- Configuring Dual VAS ID
- Traffic statistics
Chapter 13: Meridian Mail configuration
- Meridian Mail call processing
- Configuring Meridian 1 for Meridian Mail
- Configuring Meridian Mail for Host Enhanced Voice Processing (HEVP)
Chapter 14: Software installation, upgrade, and update procedures
Chapter 15: Link configuration
- Default configuration
- Link 0 - Application Module Link
- Link 1 - X.25 protocol (Meridian Link)
- Link 1 - TCP/IP host link protocol (Meridian Link)
- Link 2 - Meridian Mail Link (optional for Meridian Link)
- Changing your configuration
Chapter 16: Additional application configuration
Chapter 17: Hardware upgrade
Chapter 18: Acceptance testing
- Meridian Link/CCR
- Meridian Mail
Chapter 19: Single Terminal Access
- Hardware and software requirements
- Before you begin
- Setting up STA
Chapter 20: Ordering
List of terms
Index
Back