KEYENCE IV Series - Manual (Page 302)

A-46 - IV Series User's Manual (Monitor) -
A
Index
Shortening the processing time of
the Outline tool ..................................................5-41
Shortening the processing time of
the position adjustment......................................5-42
Specification of I/O circuit and
current of the sensor..........................................2-14
Specifications ......................................................8-2
Specifying sensor to be connected by
IP address .........................................................3-10
Stabilizing by correcting the misaligned target
position ..............................................................5-36
Stabilizing the Color Area/Area tool ...................5-39
If the area search becomes unstable due to
unwanted colors being extracted .................5-39
If the color to be judged cannot be detected ...5-39
Stabilizing the Judgment Process .....................5-32
Stabilizing the judgment process by
taking a clear image of the target ......................5-32
Stabilizing the Outline tool .................................5-38
If the detection becomes unstable due to
the effect of the unwanted outline
other than the target ....................................5-38
If the match rate difference between
the high and low-quality-targets is small ......5-39
If the outline cannot be detected
when the target becomes out of position .....5-38
If the outline of the target cannot be
detected .......................................................5-39
If the target tilts and the outline cannot be
detected .......................................................5-39
Stabilizing the position adjustment ....................5-37
If the outline of the reference target
cannot be detected ......................................5-38
If the position adjustment becomes
unstable due to the effect of
the unwanted outlines ..................................5-37
If the target tilts and the position
adjustment becomes unstable .....................5-37
Starting and finishing the Tool Auto Tuning .......5-16
Starting an Operation ..........................................5-2
Starting the Settings Navigator ............................4-3
STATUS indicator light ...................................... A-33
Status table......................................................... A-2
Stylus ....................................................... 1-10, 8-12
Switching the display to the full-screen mode .....5-5
System..................................................... 6-25, 6-45
System Configuration ..........................................1-2
T
Things can be performed with the program
functions ..............................................................6-8
Tilt Correction ....................................................6-38
Time ...................................................................6-51
Tool Auto Tuning (Automatically
Adjusting the Judgment Condition)....................5-15
Tool Auto Tuning by the previous registration
information .........................................................5-26
Tool name ................................................ 4-39, 4-49
Tool settings.......................................................5-36
Total Status Conditions ......................................4-65
Touch Panel Calibration.....................................6-52
Touch Screen Lock ............................................6-50
Transfer Condition Settings ...............................6-34
Transfer Destination Folder Settings .................6-35
Transferring the settings backed up in the USB
memory to the sensor ........................................6-21
Trigger number ..................................................5-10
Troubleshooting ................................................ A-19
Turning on the power and starting an operation ...5-2
Types of tools ....................................................4-28
U
Unmounting from the DIN mounting adapter .....2-11
Unmounting from the wall mounting adapter .......2-9
Unmounting the sensor .......................................2-5
Update Monitor ..................................................6-53
Updating the sensor ..........................................6-44
USB memory (1GB) ...........................................1-10
Useful features during installation/adjustment .....6-4
Useful features while running ..............................6-2
Using the Auto Brightness Adjustment ..............5-35
Using the digital zooming function .....................5-32
Using the dome attachment....................... 2-6, 5-35
Using the image files saved in
the USB memory ...............................................5-15
Using the image history saved in the sensor .....5-15
Using the images taken in the Test mode ..........5-15
Using the polarizing filter attachment ........ 2-7, 5-35
Using the program functions (changing over)....6-10
When the [External IN] is selected in the
Program Switch Method ..............................6-11
When the [Monitor/PC] is selected in
the Program Switch Method ........................6-10
Using with the intelligent monitor (IV-M30) ..........1-4
Using with the IV-Navigator (IV-H1) .....................1-5
V
Voltage input
(When the PNP output is selected) ...................2-14
W
Wall mounting adapter ..............................1-11, 8-12
When the NPN output is selected......................2-14
When the PNP output is selected ......................2-14
White Balance (for color type only)....................6-41