Rockwell Automation 8520-ARM2 9/Series CNC AMP Reference Manual Documentation Set User Manual
Page 752

9/Series CNC AMP Reference Manual
Index
I--x
Servo Off, (Analog), 7-27
Servo Parameters, 41-15, 41-16, 41-17, 41-18, 41-19, 41-20
22KW Shunt Resistor Pack, 7-23
5KW & 10KW Shunt Resistor Pack, 7-24
Digital, 7-87
Friction, 7-107
General, 7-5
online, 40-13
Position Loop, 7-24
Spindle, 7-100
Velocity Loop, 7-60
Servo Position Loop Type, (Analog), 7-24
Set Process Priority, 3-19
Sharable Axis, 4-14
Shift Direction, for fine boring, 25-5
Shift, Q word in Fine Boring, 25-4
Shrinkage direction, 27-5
Shunt Resistor Pack
22KW, 7-23
5KW & 10KW, 7-24
Sign of Position Feedback, 7-53
Sign of Velocity Feedback, (Digital), 7-66
simulated spindle, 4-7
Single digit feedrates, 9-9
Skip Cycle Feedrate Parameters, 9-10
Skip Feedrate For G31/G37, 9-12
Smallest Jog Increment, 8-14
Software Overtravel Parameters, 6-13
Software Overtravel Used, 6-13
Special Software Parameters, 39-1
Specifying
Axis Names, 3-3
Axis Types, 3-5
Spindle 1 Gain, 12-18
Spindle 2 Gain, 13-18
Spindle 3 Gain, 14-18
Spindle DAC Output Ramping, 12-4, 13-4, 14-4
Spindle Deviation Tolerance, 12-7, 13-7, 14-7
Spindle Marker Calibration, 12-13, 13-14, 14-14
Spindle Orienting Parameters, 12-12, 13-13, 14-13
Spindle Parameters, 7-100, 40-14
Spindle Servo Board for Axis, Analog, 7-104
Spindle Type for Axis, analog, 7-103
Spindles
Assigning to Analog Servo Module, 7-104
Configuring more than one, 3-6
exclusive-use, 4-7
No of Teeth On Motor Gear, (Digital Spindle), 7-105
No of Teeth On Spindle Shaft, (Digital Spindle), 7-106
number, 7-103
simulated, 4-7
Specifying Type, 3-5
using a 1326 motor, 7-100
Spindles Process, 4-7
Split Axis Parameters, 36-1
Deskew Gain, 36-11
Deskew Master Servo Name, 36-6
Deskew Slave Servo Name, 36-9
Excess Skew Limit, 36-13
Parameters copied from master to slave, 36-6
Stabalizing servos, online parameters, 40-13
Standard Motor Table Values, (Digital), 7-12
Static Friction Compensation, 7-107
Stiction Compensation, Torque Percent, 7-109
Storing AMP, 41-20
Subprogram option, 26-7
Suppression Point, Feedrate, (Analog), 7-32
Synch Gain, 15-6
Synchronized Spindle Parameters
Controlling Spindle, 15-2
Default Position Offset, 15-7
Follower Orientation, 15-5
Follower Spindle, 15-3
Maximum Deviation, 15-8
Seek Timeout, 15-9
Seek Tolerance, 15-8
Synch Gain, 15-6
System Scan Time, 37-20, 41-6
Examples of Setting, 37-24
Guidelines for Setting, 37-24
System Timing, Screen, 37-22
System timing, Analyzing, 37-21