Lenze 8400 StateLine - Manual (Page 730)

15 Parameter reference
15.2 Parameter list | C00700
730
Lenze · 8400 StateLine · Reference manual · DMS 12.0 EN · 06/2014 · TD05/TD14
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C00700
Parameter | Name:
C00700 | LA_NCtrl: Analog connection list
Data type: UNSIGNED_16
Index: 23875
d
= 5D43
h
Connection parameters for "Actuating drive speed" application: 16-bit inputs
• Selection of the 16 bit output signals to be connected to the 16 bit input signals
• The selection list contains all 16 bit output signals which can be assigned to the 16 bit inputs displayed by the
subcodes.
Selection list
See
selection list - analog signals
Subcodes Lenze setting Info
C00700/1 20005: LS_ParFix: wDriveCtrl LA_NCtrl : wCANDriveControl
Input for control word from CAN to device control
C00700/2 20005: LS_ParFix: wDriveCtrl LA_NCtrl : wMCIDriveControl
Input for control word from communication interface to
device control
C00700/3 20012: LS_ParFree_a: nC472_3_a LA_NCtrl : nTorqueMotLim_a
Input for maximum torque in motor mode
C00700/4 20013: LS_ParFree_a: nC472_4_a LA_NCtrl : nTorqueGenLim_a
Input for maximum torque in generator mode
C00700/5 0: Not connected LA_NCtrl : nPIDVpAdapt_a
Input for adapting the PID controller gain
C00700/6 0: Not connected LA_NCtrl : nPIDActValue_a
Input for actual PID controller value
C00700/7 16000: LS_AnalogInput: nIn1_a LA_NCtrl : nMainSetValue_a
Input for main speed setpoint
C00700/8 0: Not connected LA_NCtrl : nAuxSetValue_a
Input for additional speed setpoint
C00700/9 0: Not connected LA_NCtrl : nGPAnalogSwitchIn1_a
Input for analog switch - analog signal 1
C00700/10 0: Not connected LA_NCtrl : nGPAnalogSwitchIn2_a
Input for analog switch - analog signal 2
C00700/11 0: Not connected LA_NCtrl : nGPArithmetikIn1_a
Input for arithmetic function - analog signal 1
C00700/12 0: Not connected LA_NCtrl : nGPArithmetikIn2_a
Input for arithmetic function - analog signal 2
C00700/13 0: Not connected LA_NCtrl : nGPMulDivIn_a
Input for analog signal for multiplication/division
C00700/14 0: Not connected LA_NCtrl : nGPCompareIn1_a
Input for comparison operation - analog signal 1
C00700/15 0: Not connected LA_NCtrl : nGPCompareIn2_a
Input for comparison operation - analog signal 2
C00700/16 0: Not connected LA_NCtrl : nVoltageAdd_a
Input for additive voltage boost
C00700/17 0: Not connected LA_NCtrl : nPIDInfluence_a
Input for influence signal of PID controller correcting
variable
C00700/18 0: Not connected LA_NCtrl : nPIDSetValue_a
Input for PID controller setpoint
C00700/19 0: Not connected LA_NCtrl : nPWMAngleOffset
Input for pulse width modulation phase offset
C00700/20 0: Not connected LA_NCtrl : nBoost_a
Input for additional setpoint for motor voltage at speed
= 0