Lenze 8400 StateLine - Manual (Page 451)

Lenze · 8400 StateLine · Reference manual · DMS 12.0 EN · 06/2014 · TD05/TD14
451
9 Diagnostics & error management
9.9 Error messages of the operating system
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
 xx.0123.00094 0x175e 5982 8061022 FC01: Switching frequency reduction No Reaction C00590 0x2000
 xx.0123.00095 0x175f 5983 8061023 FC02: Maximum speed for Fchop No Reaction C00588 0xF000
 xx.0123.00099 0x1763 5987 8061027 FC03: Field controller limitation No Reaction C00570/4 0xF000
 xx.0123.00057 0x1739 5945 8060985 Id1: Motor data identification error Fault - 0xF000
 xx.0123.00058 0x173a 5946 8060986 Id3: CINH identification WarningLocked - 0xF000
 xx.0123.00059 0x173b 5947 8060987 Id4: Resistance identification error Warning - 0xF000
 xx.0123.00074 0x174a 5962 8061002 Id5: Pole position identification error Fault C00643/1
 xx.0123.00060 0x173c 5948 8060988 Id7: Motor control does not match motor data Information C00571/1 0xF000
 xx.0123.00061 0x173d 5949 8060989 Id8: Speed sensor has not been set Fault C00571/2 0x7120
 xx.0123.00145 0x1791 6033 8061073 LP1: Motor phase failure No Reaction C00597 0x3000
 xx.0123.00015 0x170f 5903 8060943 LU: DC bus undervoltage Trouble C00600/1 0x3100
 xx.0123.00016 0x1710 5904 8060944 oC1: Power section - short circuit Fault - 0x2000
 xx.0123.00017 0x1711 5905 8060945 oC2: Power section - earth fault Fault - 0x2000
 xx.0119.00050 0x1332 4914 7798834 oC5: Ixt overload Warning C00604 0x2000
 xx.0123.00105 0x1769 5993 8061033 oC6: I2xt motor overload Warning C00606 0x2000
 xx.0123.00007 0x1707 5895 8060935 oC7: Motor overcurrent Fault - 0x2000
 xx.0123.00030 0x171e 5918 8060958 oC10: Maximum current reached No Reaction C00609 0x2000
 xx.0123.00071 0x1747 5959 8060999 oC11: Clamp operation active Fault - 0xF000
 xx.0123.00065 0x1741 5953 8060993 oC12: I2xt brake resistor overload Fault - 0xF000
 xx.0123.00090 0x175a 5978 8061018 oC13: Maximum current for Fch exceeded Fault - 0xF000
 xx.0123.00096 0x1760 5984 8061024 oC14: Direct-axis current controller limitation No Reaction C00570/1 0xF000
 xx.0123.00097 0x1761 5985 8061025 oC15: Cross current controller limitation No Reaction C00570/2 0xF000
 xx.0123.00098 0x1762 5986 8061026 oC16: Torque controller limitation No Reaction C00570/3 0xF000
 xx.0123.00031 0x171f 5919 8060959 oC17: Clamp sets pulse inhibit No Reaction C00569/1 0xF000
 xx.0119.00001 0x1301 4865 7798785 oH1: Heatsink overtemperature Fault - 0x4000
 xx.0119.00015 0x130f 4879 7798799 oH3: Motor temperature (X106) triggered Fault C00585 0x4000
 xx.0119.00000 0x1300 4864 7798784 oH4: Heatsink temp. > shutdown temp. -5°C No Reaction C00582 0x4000
 xx.0123.00032 0x1720 5920 8060960 oS1: Maximum speed limit reached No Reaction C00579 0x8400
 xx.0123.00033 0x1721 5921 8060961 oS2: Max. motor speed Fault - 0x8400
 xx.0123.00001 0x1701 5889 8060929 ot1: Max. torque reached No Reaction C00608 0x8300
 xx.0123.00093 0x175d 5981 8061021 ot2: Speed controller output limited No Reaction C00567 0xF000
 xx.0123.00014 0x170e 5902 8060942 OU: DC bus overvoltage Trouble - 0x3100
 xx.0144.00001 0x2c01 11265 9437185 PS01: No memory module Warning - 0x6300
 xx.0144.00002 0x2c02 11266 9437186 PS02: Invalid par. set Fault - 0x6300
 xx.0144.00003 0x2c03 11267 9437187 PS03: Invalid device par. set Fault - 0x6300
 xx.0144.00004 0x2c04 11268 9437188 PS04: Invalid MCI par. set Fault - 0x6300
 xx.0144.00007 0x2c07 11271 9437191 PS07: Invalid memory module par. set Fault - 0x6300
 xx.0144.00008 0x2c08 11272 9437192 PS08: Invalid device par. Fault - 0x6300
 xx.0144.00009 0x2c09 11273 9437193 PS09: Invalid par. format Fault - 0x6300
 xx.0144.00010 0x2c0a 11274 9437194 PS10: Memory module binding invalid Fault -
 xx.0123.00205 0x17cd 6093 8061133 Sd3: Feedback system open circuit Fault C00586 0x7300
 xx.0123.00200 0x17c8 6088 8061128 Sd10: Speed limit for feedback system 12 Fault C00607 0x7300
 xx.0111.00002 0x0b02 2818 7274498 Su02: One mains phase is missing Warning C00565 0x3000
 xx.0111.00003 0x0b03 2819 7274499 Su03: Too frequent mains switching Fault - 0x3000
 xx.0111.00004 0x0b04 2820 7274500 Su04: CU Insufficiently Supplied Warning - 0x3000
 xx.0111.00006 0x0b06 2822 7274502 Su06: Mains input overload Fault - 0x3000
Error number Display in Error message Response
(Lenze setting)
can be set in CAN
Emergency
Error Code
32 bits 16 bits
hex
16 bits
dec
C00162/1