Index – Lenze 8400 StateLine User Manual
Page 1026
Index
1026
Lenze · 8400 StateLine · Reference manual · DMS 12.0 EN · 06/2014 · TD05/TD14
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Port block "LP_CanIn4"
Port block "LP_CanOut1"
Port block "LP_CanOut2"
Port block "LP_CanOut3"
Port block "LP_CanOut4"
Position encoder selection (C00490)
Power section ID (C00093)
Power-on time meter (C00179)
Pre-defined error field (I-1003)
Printing the interconnection
Process data objects, identifiers
Processing time
Producer heartbeat time (I-1017)
Product type code (C00203)
PS01: No memory module (error message)
PS02: Par. set invalid (error message)
PS03: Par. set device invalid (error message)
PS04: Par. set Mci invalid (error message)
PS07: Par. memory module invalid (error message)
PS08: Par. device invalid (error message)
PS09: Par. format invalid (error message)
PS10: Memory module binding invalid (error message)
PSM
Activate Lss sat. char. (C02859)
Imax Lss saturation characteristic (C02855)
Lss saturation characteristic (C02853)
Maximum motor current field weakening (C00938)
PTC
PW protection config MCI (C00510)
PW protection config X1(CAN) (C00509)
PW protection config X6(DIAG) (C00508)
PW protection internal config (C00506)
R
Rated device current (C00098)
Rated heat amount of brake resist. (C00131)
Rated motor current (C00088)
Rated motor frequency (C00089)
Rated motor power (C00081)
Rated motor speed (C00087)
Rated motor torque (C00097)
Rated motor voltage (C00090)
Rated power - brake resistor (C00130)
Reduc. brake chopper threshold (C00174)
Reference project
Remote
Acceleration/deceleration time (C00461)
Control (C00462)
MCK control (C00463)
Monitoring timeout (C00464)
Setpoint selection (C00729)
Reset error message
Reset node (CAN)
Reset time Imax/M controller (C00074)
Resp. to brake resist. overtemp. (C00574)
Resp. to CAN bus connection (C00592)
Resp. to CANx_IN monitoring (C00593)
Resp. to communication error with MCI (C01501)
Resp. to control word error (C00594)
Resp. to controller limitations (C00570)
Resp. to DC-bus voltage (C00600)
Resp. to device overload (Ixt) (C00604)
Resp. to earth fault (C00602)
Resp. to fan failure (C00566)
Resp. to heatsink temp. > shutdown temp. -5°C (C00582)
Resp. to LS_SetError_x (C00581)
Resp. to mains phase failure (C00565)
Resp. to max. freq. feedb. DIG12/67 (C00607)
Resp. to max. speed at switching freq. (C00588)
Resp. to max. speed/output freq. reached (C00579)
Resp. to maximum current (C00609)
Resp. to maximum torque (C00608)
Resp. to motor overload (I²xt) (C00606)
Resp. to motor overtemp. PTC (C00585)
Resp. to motor phase failure (C00597)
Resp. to open circuit AINx (C00598)
Resp. to open circuit HTL encoder (C00586)
Resp. to operating system error (C00580)
Resp. to peak current (C00569)
Resp. to PLI monitoring (C00643)
Resp. to speed controller limited (C00567)
Resp. to switching frequency reduction (C00590)
Resp. to too frequent AutoFailReset (C00189)
Resp. to wrong controller setting (C00571)
Reversing the phase sequence
Rotor displacement angle detection after controller enable
RPDO1 communication parameter (I-1400)
RPDO1 mapping parameter (I-1600)
RPDO2 communication parameter (I-1401)
RPDO2 mapping parameter (I-1601)
RPDO3 communication parameter (I-1402)
RPDO3 mapping parameter (I-1602)
RPDO4 communication parameter (I-1403)
RPDO4 mapping parameter (I-1603)
Running time (C00180)
S
Safety functions
Safety instructions
Safety module
Saturation characteristic
SC
Depth of current setpoint filter (C00272)
Filter time const. DC detection (C00280)
Freq. current setpoint filter (C00270)
Max. acceleration change (C00274)
max. output voltage (C00276)
Settings (C00079)