Brocade Network Advisor IP User Manual v12.3.0 User Manual
Page 1163
Brocade Network Advisor IP User Manual
1111
53-1003153-01
SAN real-time performance data
34
lists the additional counters for which you can obtain performance statistics.
TX% / RX%
FCIP
N/A
N/A
TX% or RX% = ((bytes transferred) / (maximum bytes
transmitted))*100 where maximum bytes transmitted = tunnel
speed * 134217728 (maximum bytes transmitted 1 Gbps).
If utilization is less than 1, the value is 0.0.
TX% / RX%
(Pre-Fabric OS
6.4.1 release)
TE
N/A
N/A
TX% or RX% = ((TX or RX) /
((105000000 * 10)*
(polling interval
))) * 100
If utilization is less than 1, the value is 0.0.
Cumulative
Compression
Ratio
FCIP
N/A
.1.3.6.1.4.1.1588.4.1.1.4
Compression Ratio = current value/ 1000
The compression ratio is the current compression ratio value.
Current
Compression
Ratio
FCIP
N/A
N/A
(ifHCInOctets + ifHCOutOctets) /
fcipExtendedLinkCompressedBytes
Receive EOF
TE
.1.3.6.1.2.1.16.1.1.1.5
Receive EOF = delta value
/
(1000 * 1000)
Other
3
Other counters = delta value
1.
The difference of the value retrieved between two consecutive polling cycles.
2.
The duration between two polling cycle in seconds.
3.
Additional performance counters are detailed in
TABLE 94
Performance statistic counters
Counter name
Type
Protocol Source OID value
Formula
TABLE 95
Performance counters
Counter name
Type
Protocol
Source OID value
CRC Errors
FC
SNMP
.1.3.6.1.3.94.4.5.1.40
Signal Losses
FC
SNMP
.1.3.6.1.3.94.4.5.1.43
Sync Losses
FC
SNMP
.1.3.6.1.3.94.4.5.1.44
Link Failures
FC
SNMP
.1.3.6.1.3.94.4.5.1.39
Sequence Errors
FC
SNMP
.1.3.6.1.3.94.4.5.1.42
Invalid Transmissions
FC
SNMP
.1.3.6.1.3.94.4.5.1.41
Rx Link Resets
FC
SNMP
.1.3.6.1.3.94.4.5.1.33
Tx Link Resets
FC
SNMP
.1.3.6.1.3.94.4.5.1.34
C3 Discard
FC
SNMP
.1.3.6.1.3.94.4.5.1.28
C3 Discard Rx Timeout
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.27.1.25
C3 Discard Unreachable
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.27.1.26
C3 Discard Tx Timeout
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.27.1.27
C3 Discard Others
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.27.1.28
Encode Error Out
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.27.1.29
Temperature
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.28.1.1.1
Voltage
FC
SNMP
.1.3.6.1.4.1.1588.2.1.1.1.28.1.1.2